Recent content by EHinSC

  1. E

    JD 5420 Tilt Steering Wheel Cylinder

    Edit: Finally got the stubborn pin out. Ended up finding the right sized C-clamp to hold the bracket that the pin fits in. That was enough to allow the pin to drive out
  2. E

    JD 5420 Tilt Steering Wheel Cylinder

    Thought the replacement of this small cylinder would be an easy task but found out not so much! The tilt feature gave up the ghost and now the steering wheel will not stay in any up position, it just falls in your lap. I have access to the old cylinder but driving the pin out at the bottom has...
  3. E

    Deutz fahr km22 drum mower bushing

    Gary, I had one of those Duetz mowers several years back. It had been sitting in a old barn for years and bought it for $150. PO said it had "a bad bearing". Short story, I ended up rebuilding almost the entire mower :wink: . I found that I could cross reference almost all of the bearings...
  4. E

    JD 963 Running Gear Questions

    Leroy, Sounds like you have built and used a number of wagons, and I appreciate very much the benefit of your (and others) experience! As I summarize from the posts to date, it appears that I can either leave the springs in and build the bed on them or remove them and drop the stringers down to...
  5. E

    JD 963 Running Gear Questions

    WI Dan, Thanks for the dimensions that helps me to source materials and get started on this project! Ed PS- Know some folks from Phillips area, and Waupon. Are you close to either?
  6. E

    JD 963 Running Gear Questions

    Thank You for all of the replies! Joe W, I wondered if anyone would comment on the poison ivy when I took the picture! The gear has not been rolled, it is just "old" looking due to being stored outside for several years. It trails straight as an arrow at hwy speeds (empty) so I think I have a...
  7. E

    JD 963 Running Gear Questions

    I have this older 963 JD running gear that was originally set up to haul peach crates and has the leaf springs on the axles. What (if anything) would I need to do to convert this to a hay wagon? Can I build the new deck directly to the existing brackets on the springs?I know new tires are in...
  8. E

    John Deere TY 1800 H Generator

    LJD, You do not happen to have the generator with the broken manifold still around for parts do you? I sure could use that coil as I am coming up empty with my search. Thanks!
  9. E

    John Deere TY 1800 H Generator

    Thanks guys for the help! I think that it was mfg. by Kawasaki and that the coil is #21171-2100. So far, I have been unable to locate it, however I know that there has to be at least 1 of them out there somewhere. Any suggestions would be most welcome. Thanks again, Ed
  10. E

    Grain drills/seeders

    Thanks for the reply! I will be using mostly in hay fields but no till would work in prepared fields too right? What models should I be looking for in 10 - 12 ft models (to cover tracks)and are there any obvious things to look for in a used machine?
  11. E

    JD in tornado damage

    Welcome to the Carolinas! Wife and I have been here since 1980, moved around the SE some (business) but left IL in 1972. Only warm up the snow shovel about once a year!
  12. E

    JD 5420 hour meter codes?

    Jim, No they are not in the owner's manual, but I have an interesting discovery. What I thought was an error code appears to be a malfunctioning digital readout. I decided to just tap on the hour meter and low and behold it flashed 804.3 and then back to what appeared to be PJ43! This is the...
  13. E

    5425 Power Steering Line Leak

    For what it"s worth I have a 5420 purchased new that in the first year developed a hole in the power steering hard line. It was rubbing the tractor frame. Dealer nor Deere would do anything for me. Cost around $300 for the repair.
  14. E

    JD 5420 hour meter codes?

    While mowing noticed the hour meter reading P_40, then 41,42,43. Anyone know what these mean? Is there a place other than dealer to get this information? Thank You!
  15. E

    JD 5420 Showing high temps

    Rod, I suspect you are correct and I have been looking for just such a situation but have come up empty! Will keep looking, as there is a gremlin there somewhere. Sure hope it is not the gauge, cause addording to JD Parts the whole instrument panel would need replaced and it is $500. PS tractor...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top