(800) 853-2651
SHOP NOW

Recent content by EliG

Yesterday's Tractor Forums
  1. E

    part number for Case CK 930 gas engine

    The numbers in my previous post were for the comfort king. If you have a comfort king western special the numbers are A24714 for the rear one and the front is A24715.
  2. E

    part number for Case CK 930 gas engine

    There are two numbers for the gas manifold parts. The back one is A24547 and the front one where the exhaust goes through the hood is A32614. The numbers are different if your have an LPG tractor. Eli
  3. E

    Case 400 diesel pros cons

    How big of snow blower are you planning on using and how much snow do you get a year? I put an 8' two stage snow blower on my 400. I made a heavy duty top link bracket that bolts below the existing top link bracket. We made special pins for the lift arms to attach the eagle hitch arms to...
  4. E

    Plow pix

    I think that must be a 4 bottom BER that has a bottom removed to be a 3 bottom based on how the trip mechanism is set up. Eli
  5. E

    Need help with a Case DC

    Congrats on the new tractor! Your can weld uplease the drawbar support and drill new holes. It would be good to practice on since it will need to be ground down once it's welded up. Good luck!
  6. E

    Must be Monday!

    Hey now! My main saw is a Pioneer and it starts and runs great. With a sharp chain it will easily keep up with the equivalent size Sthil saw. Eli
  7. E

    Case 220 Hydraulic Drive Issue

    Is it possible for the brake to be stuck on? Eli
  8. E

    Still ok to post here?

    Jon, Just paint over those forbidden words and tell folks it's from the 40's or 50's. It's close enough to the Case implement green that was used in that era.
  9. E

    Case 401

    The screen does not come off it is brazed onto the end of the pipe. The orings that I mentioned are behind the valve body/pump. If you pull the valve body/pump you can get to the bolts that hold the suction tube in and then remove it to clean it. Good luck!
  10. E

    Case 401

    When you pull the filter out you can see the intake screen for the pump through the filter hole. Another potential cause for your issue could be the two orings that seal the pump to the hydraulic housing or the pump is just plain wore out.
  11. E

    Case 400 Diesel Pros - Cons

    A few other things that I though of. The eagle hitch is really close to a category 1 3point. Most category 1 implements will fit or can be modified to fit. The top link for the eagle hitch bolts over the pto. If it is missing you should be able find one. The shift pattern uses a double...
  12. E

    Case 400 Diesel Pros - Cons

    If it runs decent you should be ok. As others have said the hardest things to find are injector pump parts. I went through my 400 from the radiator cap to the draw bar. I was able to find all of the parts that I needed or made my own. Good luck!
  13. E

    Today's funny

    My patients does not last that long after about 15 minutes out comes the torch. It can't be stuck if it's a liquid!
  14. E

    930 CK Hydraulic Valve

    I went back and checked the shop manual and it does talk about the two different valves used. It does not describe if there are any differences in how to set the relief valve between the two. You can purchase shim stock in varying thicknesses and make your own. As I mentioned in an earlier...
  15. E

    930 CK Hydraulic Valve

    That is correct. Check your pressure again after changing he shims. If your pump is good it should be pretty close.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top