-
-
P
9N lift cylinder spring
I have 2 springs on the cylinder that doesn t appear in the parts manual. I put them back on. Has anyone seen this before. I can’t upload the pictures. This post was edited by Panaman on 09/07/2022 at 07:01 pm.- Panaman
- Post #1
- Forum: Ford 9N, 2N & 8N
-
O
Whats for supper
Tomatoes, cucumber, a beet all from the garden. And other veggies in a tortilla shell. Thats only 1/5 of a beet.- Old560
- Post #1
- Forum: Tractor & Farm Talk
-
A
Winter Oil
Whats a good winter weight oil to run in the D14 Gasoline Engine. Middle Of State Of Wisconsin- Army
- Post #1
- Forum: Allis-Chalmers
-
T
vintage windshield wiper kit
Came across this in a job lot at an auction in relatively good shape. I am assuming it is relatively old, just wondering if anyone would know the approximate vintage? Ever seen before? I assume its something a garage/dealer would have kept on hand? Any info on and what it might be worth would... -
T
JD Model D Engine Parts
Good afternoon, Does anyone know where a guy can get a set of main bearings and seals? I pretty much having a tough time finding any parts for a model D.- Tnbshr
- Post #1
- Forum: John Deere
-
Sunday Rust Pic
- kcm.MN
- Post #1
- Forum: Tractor & Farm Talk
-
S
Picked up a winter job
To help support the crawler project and maybe buy a cab for the 3020 . Been working on some potato equipment and have a bunch of potato trucks to service and do brakes on through the winter until the ground thaws and drys up in the spring . One of my favorite projects for the winter is to do an...- SVcummins
- Post #1
- Forum: Tractor & Farm Talk
-
Plumbing loader into 3020 direct?
I have an early 3020 (hyd on dash) syncro trans that I want to run the loader valve direct instead of thru the rear hyd outlets. Will get pressure at fitting in front of brake valve. I want to run the return over to the housing behind the hyd filter. Which line do I want to tee the return into...- tomstractorsandtoys
- Post #1
- Forum: John Deere
-
G
front loader
Anyone know what model tractors a Ford loader model 2246QT will mount to? thanks, gregjo1948- gregjo1948
- Post #1
- Forum: Ford
-
T
Carb rebuild update.
I posted a week or so ago about a carb rebuild gone bad on me. I used the jets in the kit which made the tractor run like garbage. I put all the original jets and needles back in and boom, she runs great again. Now on to the next problem, I will start a new post on that. The main jet was tiny...- Tractoman
- Post #1
- Forum: Ford 9N, 2N & 8N
-
S
Scotts battery discharge
Own a Scotts 25/54 that has had a charging light problem for years and finally bit the dust. History; for yrs the discharge light would come on for a while then not. Sometimes it'd stay on the entire time I cut grass but never had a dead battery problem. I'd replaced the regulator but changed...- spikeit53
- Post #1
- Forum: Tractor & Farm Talk
-
B
Oliver 70 RC Distributor
I'm restoring my dad's Oliver 70. It has a distributor but the copy of the service manual I have only addresses a magneto. A few questions. Timing. Should it be timed on the flywheel marks for the magneto or at some other position? Gap width on the distributor points? Thanks. B'duckie- Bobduck
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
'39 Aluminum hood auction
A friend texted me and the Auction's over the '39 aluminum hood bought $9450. I would have thought it would have bought less then half that price because of all the non early '39 parts that had been switched out. It only takes two people who want it to turn it into stupid money. Hope the buyer...- Kirk-NJ
- Post #1
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy