(800) 853-2651
SHOP NOW

Recent content by emt3992

Yesterday's Tractor Forums
  1. E

    70 Belt Change

    Thanks guys!! Yes I expect a few beat up knuckles
  2. E

    70 Belt Change

    maybe.. but it still has to pass between all of the blades and the shroud and have enough length to clear the whole fan
  3. E

    70 Belt Change

    So how hard is it to change the belt on my 70? Haven?t yet but grabbed a new one with an order I placed. I?m hoping I can slip it over the fan and not need to pull anything?
  4. E

    Power steering

    Thanks Bob!! That?s pretty much where I found the pieces of the paper washers and where I guessed they went. Definitely confirmed now. I?ll check the bushings when I get home they must be there bc I never pulled them (I hope)
  5. E

    Power steering

    Thanks Dan! You were a huge help keeping me moving with this project! I think you?re right, those bushings are probably pressed into the pedestal casting because they definitely didn?t come out with the shaft. I almost put it back together last night but right when I started replacing o-rings, I...
  6. E

    Power steering

    I need to order a manual I guess. My problem is these ?bushings? don?t even exist on mine... I wouldn?t have seen it known about them until I saw them listed on that diagram
  7. E

    Power steering

    Anyone familiar with a power steering pedestal re-build? I have all parts and ready to assemble except these two ?bushings? They were not on it when I took it apart, but the diagram shows them. They?re $50 a piece so I?m trying to figure out if they?re even needed ??
  8. E

    Steering Spindle

    While rebuilding my leaking power steering on my 70 I came across this.. something ripped the edge of the spindle by the bearing. The bearing is still seated right and no gaps there. But would this leak if left alone or does the fluid not reach that low since all of the seals are above the cork...
  9. E

    PS Pedestal

    Thanks! Yeah I just looked at pics from a couple other rebuilds and saw theirs bent onto each bolt.
  10. E

    PS Pedestal

    gotcha. thanks. nothing came loose and no other damage. is it supposed to be bent onto the bolts? it does stick up a bit above the steering vane when flat.
  11. E

    PS Pedestal

    I finally got it apart! Had to heat the gear to break it free, then heat the casing and tap the lower half to get the shaft to drop. Looked normal, pretty gummed up. But I found this bent piece interesting.. thoughts??
  12. E

    PS Pedestal

    Thanks Dan!! Yes i built a box and following the pictures you sent me from my last post. Everything but the heat part. I?ll start heating the gear today when I get back on it. Also just a little nervous about getting it back together and seated right after I put the new the o-rings in.
  13. E

    PS Pedestal

    Am I missing something or is there a trick to separating the pedestal? I have the pedestal lifted out, but can?t get the gear off the top so that the shaft will drop out. I left the bolt in and have been hitting that, maybe I just need a heavier sledge. I?ve tapped on the gear a little but don?t...
  14. E

    JD 70 Electr

    What? Why should I not share my experience with others? Their forum? Good! They should know that their staff is being ignorant or providing poor customer service. Same as giving someone a review. Sorry I speak up when treated poorly or receive bad customer service!
  15. E

    JD 70 Electr

    Thanks. Any thoughts on wires? I?ve read in a couple places that copper core wires are best? Haven?t really seen any of them around tho
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top