(800) 853-2651
SHOP NOW

Recent content by equinehauler

Yesterday's Tractor Forums
  1. E

    naa rear main question

    Thanks again. I thought I could get by with loosening the caps and packing a little extra in the top half and replacing the lower. It worked on my old ford 390 engine. I probably had the correct cord then. :?
  2. E

    naa rear main question

    Thanks guys, I didn't like the look of it. It is completely compacted into the groove and the entire half of the weaved outer layer is left. I figured that there wasn't anywhere for it to go and not allow the cap to seat properly and causing a spun bearing. I guess I need to order the...
  3. E

    naa rear main question

    I am talking about the entire cord, not the ends.
  4. E

    naa rear main question

    I used the side of a socket against the seal and tapped it with a light hammer. I'm afraid that if the cord is not completely in place, the cap may not seat properly in place allowing little to no support for the bearing.
  5. E

    naa rear main question

    Thanks for the reply. The picture shows what is left of the seal after tapping it into the grove. There seems to be too much material left out for the cap to bolt in correctly. Is it possible that these seals are the incorrect ones?
  6. E

    naa rear main question

    I am currently replacing the rear main seal on my 54. I dropped the pan, and removed the rear bearing cap. the rope gasket that I purchased from Stevens tractors is to large to fit into the grove. The old one looks like it didn't have any of the coated outer cover against the crank, only in...
  7. E

    NAA clutch adjustment

    With a break in the weather and spare time, I split the tractor and found my problem. Although the clutch was new enough that there wasn't any dust on it, one of the three release arms on the pressure plate lost the pin where it pivots. The pin had stuck inside the pressure plate and I wanted...
  8. E

    NAA clutch adjustment

    OUCH!! Thanks again
  9. E

    NAA clutch adjustment

    That was my plan when I purchased it. I was just hoping for a lazy way out. Thanks guys, This site has been a great reference for me.
  10. E

    NAA clutch adjustment

    Thanks guys. Does anyone know where the secret door is to repair the fork??? :roll:
  11. E

    NAA clutch adjustment

    I just purchased a NAA with a stuck clutch. After reading all of the different posts on breaking a rusted clutch plate free, I felt that this will be the problem. Well, I don't believe this to be the case. The previous owner said it worked not to long ago, then the clutch wouldn't disengage. I...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top