(800) 853-2651
SHOP NOW

Recent content by ericoberg1

Yesterday's Tractor Forums
  1. E

    Ford 1710 front steering linkage bent? Can you check you

    Hi Bern, Bob57, and JoeM(GA). Thanks! Here is the link after beating it in to submission and welding angle on two sides. Toe in very easy to adjust after cleaning out the threads and a touch of fresh grease. Painted it Ford blue after installation. A touch of red spray paint on the end that has...
  2. E

    Ford 1710 front steering linkage bent? Can you check you

    Hi All, Ford 1710 4 wheel drive. Just finished discing down weeds in our property in Southern California. Driving the tractor back to the barn, and the front end looks funny. The wheels are both like 10 degrees toed out. Did not hit the front steering linkage rod with anything, but went...
  3. E

    Ford 1710 engine block drain valve - threads?

    Hi. The threads are 1/4-19 BSP - "British Standard Pipe" (Taper). Cost about $20 for the tap. Got a new drain valve from Messicks, cost was also about $20.
  4. E

    1710

    The retrofit was not available at my local New Holland dealer. I figure it took 30 years for mine to start leaking with out the hose retrofit. Got all new o-rings, cleaned the whole mess up, and carefully aligned the valve and mounting. No leaks now for 6 months. The old o-rings all had a flat...
  5. E

    Ford 1710- good tractor?

    Made by the Shibaura, all metric hardware. I have 3050 hours on mine and still going strong. I have the 770A loader on the front. Got a bunch of new gaskets and seals from New Holland, still supported. Got a new water pump, hoses, lights from various sources. The engine blocks are getting to be...
  6. E

    Ford 1710 Differential Lock

    Hi Flembo, We have had our 1710 for 20 years. As we almost always have the tractor in 4 wheel drive, the lock never gets used. However, the pedal is a bit "weak", as in its travel is only about 2 inches till it hits bottom. Springs back up, just not very snappy. Like yours, nothing seems...
  7. E

    OT -Who Remembers This HOT Gal?

    Here is my Wife with Cassandra, out of drag. Got me a signed "action figure" (doll)!
  8. E

    Rear axle seal, Ford 1710

    Go to www.newholland.com Select agriculture Upper right "Parts Store" Find Parts By Model Search for Model, enter 1710 Select 1710 3 Cyl Compact Tractor Select Rear Axle Brake and wheel shaft case? (Dont know exactly which seal your are looking for.) Did this for a bunch...
  9. E

    Ford 772A loader parts..

    One of the 4 hard lines on my 1710 and 770A has been replaced by a hose. Working that way for over 20 years.
  10. E

    Morning commute in Camarillo, California

    This is the traffic I have to navigate on my way to work. Lots of strawberries, various vegetables, and supposedly the peppers that make up Sriracha hot sauce. The trailer thingy is used to transport implements between fields.
  11. E

    Ford 1710 Steering Dampener and brackets

    Hi Flembo, That is great information. I read in several places that the shock usually got pinched, bent, or knocked due to the exposed location. I will go out this weekend and look between the front right tire rim and the output drive hub to see if there is any marks. I bet it the whole thing...
  12. E

    Ford 1710 Steering Dampener and brackets

    Hi All Got a Ford 1710 with 4 wheel drive. It has a bracket for the steering dampener mounted in the middle of the front axle (top picture). From the NewHolland parts breakdown, there should be a bracket on the right hand side at the wheel (bottom picture, dusty from discing). Am I missing...
  13. E

    Tie downs for hydraulic hoses?

    Thanks for this, I will look for the black zip-ties. The black are supposed to be UV resistant.
  14. E

    Ford 770A loader - What is this extra tube?

    Hi Guys, thanks for this. I have the 770A loader manual, it did not show the same picture. Since my valve block is on the tractor, I can now figure out some other use for the tube.
  15. E

    Ford 1710 fuses not connecting, lights and gauges dropping

    Hi Guys, Thanks for all the ideas. Fuses are not blowing, just not connecting well enough for the lights and gauges to work. Clips seem snug. I just push the fuse back and forth a few times, things start working again. Don't know if it is the fine dust creeping in, or oxidation. Got them...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top