(800) 853-2651
SHOP NOW

Recent content by eyecatcher

Yesterday's Tractor Forums
  1. E

    Need a little help here

    roblem is, mine isn't the cast iron original, rather a Zenith. I've cleaned thoroughly & installed a kit that looks like the right one, & everything fits, but I still couldn't keep the gas from dribbling out the bottom. no #'s on this carb.
  2. E

    Need a little help here

    roblem is, mine isn't the cast iron original, rather a Zenith. I've cleaned thoroughly & installed a kit that looks like the right one, & everything fits, but I still couldn't keep the gas from dribbling out the bottom. no #'s on this carb.
  3. E

    Need a little help here

    Book says Champion H10. Don't like Chmpion plugs. What do you reccommend? What is plug gap? Is Wix 5101 right oil filter? Where can I find that list of dos & don'ts for the 8N? How can I get ahold of Royse about a carburetor?
  4. E

    Finally it"s back!

    ince I have become disabled, my wife has had to take over everything on our little 10 acre patch of land. When we got the engine back, She wanted to see if she could install it. With me setting on a stool giving instructions, not only did she get that done, but rehung the front end, tires...
  5. E

    Finally it"s back!

    ince I have become disabled, my wife has had to take over everything on our little 10 acre patch of land. When we got the engine back, She wanted to see if she could install it. With me setting on a stool giving instructions, not only did she get that done, but rehung the front end, tires...
  6. E

    Finally it"s back!

    ince I have become disabled, my wife has had to take over everything on our little 10 acre patch of land. When we got the engine back, She wanted to see if she could install it. With me setting on a stool giving instructions, not only did she get that done, but rehung the front end, tires...
  7. E

    Finally it"s back!

    I posted on here before about getting my 8n engine back from the machine sop after 9 months. Well, it never happened. Seems like the old man that owns the place, used to work on the ns years ago, & he wouldn't let anyone else in the shop touch it. He is in bad health, had an operation during...
  8. E

    Email address

    Would like to contact Royse or one of the other carb gurus, but can't find an e mail address. Classic View doesn't come up with anything. How do I find an address?
  9. E

    8n motor install

    how do I send a PM on this website?
  10. E

    8n motor install

    How do I contact him?
  11. E

    8n motor install

    Supposed to get my 8n tractor engine back from the machine shop today. Complete rebuild! Unfortunately it has been in the shop over 9 months. Both the machinist & I became ill & had major surgery. He has completely recovered. I haven't, & won't. I can't re assemble the tractor...
  12. E

    2n Generator Brushes

    DUCT TAPE
  13. E

    May have to give it up

    started to refurbish an 8N. Had it running well, hydraulics worked, metal pretty rough. Installed lots of new (and used) parts as cleaning & repainting progressed. Far too much to list here. Had to let it set for a year (health). Wouldn't run - no compression. Had one head bolt twisted off...
  14. E

    8N6276 thrust washer

    Rblding my 8n. Camshaft thrust washer/spring has a hole worn through it. Looks li8ke this was only used w/front mount distributor which I have. Unable to locate a new replacement. Where can I buy this?
  15. E

    stuck rings & MMO

    8N had no compression (0-0-5-30). It would blow my thumb off the spark plug hole, but that was all the would show on the gage. Pulled the head & checked w/straight edge - looked good. Head gasket was black on both sides, didn't look blown. Poured Kroil on top of the valves, and it seemed to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top