-
FFabrickator replied to the thread Noisey Gears.I went out to try to get the rear wheels off and they are rusted up. So I abandoned taking them off for today and went ahead and cleaned...
-
-
FFabrickator replied to the thread Noisey Gears.I finished painting the two front wheels today. They were easy to handle. I want to pull off the rears to do them, but I’m a little...
-
FFabrickator replied to the thread Noisey Gears.Decals on! I be don’t like the plastic film type, I prefer vinyl lettering. Maybe they’re meant to be a “tip of the hat” to earlier times.
-
FFabrickator replied to the thread 420W Decal locations.Oops. Forgot the pics. I lost one of my hood bolts so I’ve got to get another one. I used stainless steel socket heads.
-
-
FFabrickator replied to the thread 420W Decal locations.I did my best to get the decals on and I’m disappointed with the type, I like using vinyl letters as opposed to plastic film. I found a...
-
FFabrickator replied to the thread Noisey Gears.Thanks. Just installed the paint! I need to do some touch up but at least it’s on.
-
-
FFabrickator replied to the thread Noisey Gears.Closed up the steering box today after making one more modification. The only place that I had some play was at the compression boss...
-
-
FFabrickator replied to the thread Noisey Gears.That nut is hard to reach. Part of your sloppiness may have been a combination of the shaft and the adjusting nut allowing the...
-
FFabrickator replied to the thread Noisey Gears.I finished the new pin and installation and it turned out great. Steering slop went from about 40* to 10*. It’s really a world of...
-
-
FFabrickator replied to the thread Noisey Gears.Thanks for the tip. I can confirm my measurements I TRIED to take off of my existing junk. Mine only cost 4” of 5/8” rod stock I had on...
-
FFabrickator replied to the thread Noisey Gears.Well, I decided to try and replace the pins while I had the rad cover off. I removed the steering box cover and it was so funky with old...
-
-
FFabrickator replied to the thread Noisey Gears.Thanks, my shops have always been in 1 & 2 car garages, so when I retired and moved out of SoCal tract home neighborhoods, to NorCal on...
-
FFabrickator replied to the thread Noisey Gears.Thanks for your reply’s. Yes, I see where a new worm gear is $199 and pin are also available for cheap. Like was said, I’ll have decide...
-
FFabrickator replied to the thread Noisey Gears.I finally got some new tie rod ball joints and cut off the “power steering” mod to the steering control arms. Man, it really tighten...
-
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy