(800) 853-2651
SHOP NOW

Recent content by farmallpuller2014

Yesterday's Tractor Forums
  1. Fawteen

    Why I don't loan tools

    .
  2. F

    Farmall Super H Pulling

    I was thinking of putting the 706 D188 pistons in the super H block without the sleeves.I was just wondering if they will work with the original rods or what would have to been to them in order to make them work.It is my understanding the 3 11/16 pistons will fit in block without sleeves and...
  3. F

    IH 340 sputters then dies

    I would try taking the carb. off and take a part and clean and blow it out good to make sure there is nothing stuck in it.Then take sediment bowl off and do the same to it and the lines also.I usually add a short extension tube to the sediment bowl so it is not getting the fuel from the bottom...
  4. F

    What did I do wrong?

    make sure the wires on coil are not reversed and also make sure the points are clean and set right .20
  5. F

    losing power before traction

    Thanks for the input.I will try the vacuum guage,what is the normal vacuum range should I be looking for?I will also make sure the throttle plate is opening all the way.If there is any other suggestions I would appreciate hearing them,always willing to learn more to make my tractor better at...
  6. F

    losing power before traction

    Thanks to all I appreciate all input.You all give me alot to think about and try.I am not sure if they did a vacuum test on the dyno,I was not present at the time my brother was,it is both our tractor.I just figured there should be a noticeable RPM change when it is put under a load and I don't...
  7. F

    losing power before traction

    Thank you for your responses.I had my brother take it and had it dynoed by the president of our pulling club,so I am not sure if they manually open the throttle or what I will check on that.The tire size is 12x38 and they are not cut.It has a M carb. and yes it has a largest ventura that it...
  8. F

    losing power before traction

    I pull a super h with a 300 engine and on the dyno it it is pushing out 55 hp.(yes the engine has been redone) but when pulling it will still run out of power before it will spin a tire.Does anyone have any ideas what could cause this to happen.Could it be a governor issue or what.It doesn't...
  9. F

    Blowing head gaskets.

    I would take a flat edge and set on top of block and check for gaps with a feeler gauge,a gasket can still seal right if gap is 8-10 thousands,Also make sure to put the gasket on with right side up,the flat side down on block side and the raised edge around the cylinders are up to the head.The...
  10. F

    HP gains for super H with 300 engine what will help

    thank you for your response,do you know where I can find the lpg pistons for the c175 engine and what the HP ratings would be
  11. F

    HP gains for super H with 300 engine what will help

    Hi,I am new to the forum,so here is my question.I pull a farmall H with a farmall 300 engine and I was wondering how much HP will I gain if I shave the head .100 w/standard bore and pistons,and also what HP would I gain with the 175 piston std. or 175 LP pistons.any help or ideas would be...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top