-
-
-
R
JD 720 Diesel Rear Wheel Spacing
Hello all. Im looking at picking up a narrow front JD 720 diesel. I know the rear wheels are adjustable in width using the rack and pinion on the axle shaft. How narrow can the wheels be moved in? My trailer measures 67 or 79 wide between the fenders, will they go that narrow? Tractor Data...- rickdude
- Post #1
- Forum: John Deere
-
F
Bad hydraulic pump?
If the 3 point works ok, then there is nothing wrong with your pump, the same pump works both.- farmallsforever
- Post #1
- Forum: Farmall, International & McCormick
-
F
IH 46 baler
I had a 46 baler. I used it as a back up for my round baler. I baled around 500 bales a year with it. It worked good, but you couldn't push it too hard. I had it for about 8 years, no problems. Bill- farmallsforever
- Post #1
- Forum: Implement Alley
-
F
Inter 444 rear wheel lugs L or R hand thread?
right hand thread- farmallsforever
- Post #1
- Forum: Farmall, International & McCormick
-
F
Is it possible?
anything is possible, but WHY would you want to?- farmallsforever
- Post #1
- Forum: Farmall, International & McCormick
-
F
4366, 2 of them at auction
I stopped over at Quarrick's auction in Uniontown, Pa., just to see what will at their December auction. They have 2 really nice 4366 four wheel drive tractors. One has 2700 hours and the other one has 2900 hours. I don't need that big of tractor, but maybe some one out there is looking for one...- farmallsforever
- Thread
- Replies: 0
- Forum: Farmall, International & McCormick
-
F
John Deere 350 B
I have operated many 350's and 350B's. and they all made noise in reverse, some more than others.- farmallsforever
- Post #1
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
F
Disc Mower Gear Timing
I have always timed them, 12 o'clock-6 o'clock for the first one. Then 3 o'clock-9 o'clock for the next one. Back and forth till they are all in time.- farmallsforever
- Post #1
- Forum: Implement Alley
-
F
Need help finding row markers
I bought an Allis planter without row markers. I made a pipe setup on the front of my planter tractor. I had a chain drag on the last row I planted. I adjusted it so that the planter was spaced right. works good.- farmallsforever
- Post #1
- Forum: Implement Alley
-
F
Hatz diesel
I bought an arrow board, (used when doing road construction, shows you which lane to be in) It has a Hatz E71 diesel engine, the engine runs an alternator that charges the batteries that run the lights. I bought it thinking I would make a tractor using the Hatz engine as the power plant. How...- farmallsforever
- Thread
- Replies: 4
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy