Recent content by FerdferLife

  1. F

    Mounting a stabilizer kit Ford 3000, some advice needed

    Hi again people Thanks for all you help and advice. I read the replies here this morning and i had pretty much given up on this kit but i decided to give it another try. Sure enough as some of you mentioned, the pivotpoint didnt match that of the liftarms heightwise, the bracket pivot...
  2. F

    Mounting a stabilizer kit Ford 3000, some advice needed

    Hi People I grew tired of everything slapping around on the 3 point, so i decided to buy a stabilizer kit. THis one; The brackets on/under the axel fits fine, however on the end that i need to drill holes to attach the bars to the lift arms, im a bit confused. If i push the liftarms out...
  3. F

    Ford 3000 selector valve oring?

    Hi Folks about a year ago i ordered a selector valve oring kit, but for some reason it didnt come with the oring for the piston/valve itself, so i found one i thought would fit, but now it has started leaking again. Does anyone know what size it should be? i also dont remember how to...
  4. F

    1969 Ford 3000 clutchpedal bushings

    Thanks folks I just done this today and everything went back together fine, bushings looked fine also. Couple of questions, on the brake pedal side, theres first the seal, then the felt seal thing, then a trust washer, this trust washer isnt totally round, its cut a lil flat on one side...
  5. F

    1969 Ford 3000 clutchpedal bushings

    Thank you Sir :D
  6. F

    1969 Ford 3000 clutchpedal bushings

    Hi Folks preparing to do some repairs on my 3000, i see the oilseal on the clutchpedal axle is leaking, and quite a few people recommends changing the bushings on the clutch and brake side while the axle is out. are the bushings in the pedals itself or in the hydraulic block or whatever to...
  7. F

    Ford 3000, slow and sloppy feeling hydrualic

    Thanks for the offer of a lift cover, but im in Norway, Europe. I probably need a the leaver at least, hard to tell whatelse is needed until i get in there tho. The flowcontroll is set to fast. Does anyone know approx weight of the liftcover? it looks very heavy, so i assume you cant lift...
  8. F

    Ford 3000, slow and sloppy feeling hydrualic

    Very odd that its missing completely, i have never noticed it before even tho i have looked for the leaver before. I had the inspection cover off last summer and looked inside with a flashlight, didnt notice anything hanging from the leaver sider or any parts in the oil, but then again i...
  9. F

    Ford 3000, slow and sloppy feeling hydrualic

    Hi again Went outside today to see if i could find the leaver, and i sorta did. Theres just a hole where the leaver is supposed to be. Is it possible to use something to change the setting somehow, like a screwdriver, or go thru the inspectioncover thingy on the other side? best would be...
  10. F

    Ford 3000, slow and sloppy feeling hydrualic

    My 3000 doesnt have a selector for that as far as i can tell, it only has the fast/slow adjustment, unless the selector is somewhere i havent seen.
  11. F

    Ford 3000, slow and sloppy feeling hydrualic

    Hi again Folks My 69 3000 diesel has now done its chore showeling snow for the winter, so its time for some maintainance, during the winter i have noticed that the 3point feels very sloppy up and down when i use the leaver, like if i let it down, the 3 point pretty much just smash my blade...
  12. F

    Ford 3000 not charging below 1500 Rpm

    Alright, sounds good. Hopefully it keeps working like this and no more flat batteries. Thanks again for all ur help
  13. F

    Ford 3000 not charging below 1500 Rpm

    Thanks again for your help. I think i might have gotten lucky here. I went to measure the F and A terminal and i noticed all the connectors for the voltage reg was a bit loose, so i pulled them off, and oh my, they were seriously cruddy. I cleaned them all up and gave them a lil squeeze for...
  14. F

    Ford 3000 not charging below 1500 Rpm

    Hi again Just been out measuring the voltage again it seems to start charging at a pretty specific rpm, seems to be pretty much 1450-1500 rpms. Before it reaches that rpm, i measure 0.2 volts at the generator even at lets say 1400 rpms. at 1600 rpms it produces around 13.5v, 1800 rpms -...
  15. F

    Ford 3000 not charging below 1500 Rpm

    Yes, the charge light comes on, but i have also measured with a voltmeter to be sure.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top