-
F
How do I sharpen my diagonal cutters.?
Take a small file, and file the cutter at 90 degrees to the blade. It is called draw filing, just like drawing a knife to peal bark from a log. You put some pressure as you file away from you, and draw back lightly. You can put the pliers in a vise to hold them, -
F
Massey
Where do they sell it? Or where can you order it? I am based in https://postcodefinder.net/england/manchester. Do you think I will be able to find anything like that here? I do not need necessarily something identical. It will be enough to find a similar tractor. If someone can recommend decent...- fertooos
- Post #1
- Forum: Tractor & Farm Talk
-
F
How to drill a hole in ceramic tile?
I bought carbide hole saws off eBay that can drill through glass. -
F
3000 Clutch/Axle PIn Job Complet
It looks to me that you are doing a great job. New clutch discs usually indicate "flywheel side" -
F
Ford 800 questions
800 is the series, carefully clean where that number is on the flat spot, it might still show up if not corroded away. 850 or 860, it is likely to be one of those 2 models. It has a 5 speed lever I can see in the photo. With the clutch in the condition described, it may be difficult to determine... -
F
Ford Select O Speed Repair Advice
Don t you have any services to call in your area providers for area code 702? It would be best of all to get expert consultation. You will surely find somebody in your region. Call them and invite somebody to come. In some situations, it is better to pay for professional help, than to damage... -
F
Ford Select O Speed Repair Advice
If the tractor moves, drives and pulls in 7th gear, your problem is most definitely NOT the torque limiting clutch. Do you have any gears other than 7th? -
F
My trailer again
What's close? You've got 2500lbs of capacity left, and that's not even counting tongue weight. A minimum of 947.5lbs should be on the tongue, meaning that only 8527.5lbs of weight will be on the axles, which are rated for a combined 12,000lbs.- fertooos
- Post #1
- Forum: Tractor & Farm Talk
-
F
The best is back in the hole
My 2000 f250 7.3 power stroke has 220,000 some thousand on it, been a great truck, auto tranny never touched, I don?t plow and it?s only towing 6000# at most. I do not run it in winter, idiots put down so much salt, it would probably cost me $65000 to replace this truck with a new 2020 model...- fertooos
- Post #1
- Forum: Tractor & Farm Talk
-
F
OT Heat tape and pets
If your pet does not have a chip, it is good that it has some information re owner. It can be your address or telephone number. Or any other contact information like email. If you state your address, do not forget to give your correct postal code. Have a peek at this web-site to recheck if you...- fertooos
- Post #1
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy