(800) 853-2651
SHOP NOW

Recent content by Fins/413

Yesterday's Tractor Forums
  1. F

    8N Throttle

    Thanks Soaked I had the same issue with throttle position. I took the air cleaner of to get reasonable access, took it loose and tightened it at the correct position. Everything works as it should the rod to the governor moves straight back and forth and I can set hand feed to the closed...
  2. F

    Ford 8N (1949) Replacing rear axle seals - Project #3

    TV stands for Room Temperature Vulcanizing
  3. F

    Trouble with 51 8N starter drive engaging.

    Thanks guys It need a clutch anyway so it looks like I'll split it and get a good look.
  4. F

    Trouble with 51 8N starter drive engaging.

    There are no missing teeth but I had not considered that the ring gear could be spinning.
  5. F

    Trouble with 51 8N starter drive engaging.

    I have a 51 8N 12v conversion 3 wire alternator. It runs great when I can get it to run. It sounds as if the drive is not engaging. The fan does not spin. I have been through 3 starters two original style and one mini. I just put a brand new drive on the original starter, there was no...
  6. F

    1951 8 N hand crank extended length

    hanks I was hoping to buy one before I attempted something else.
  7. F

    1951 8 N hand crank extended length

    hanks I was hoping to buy one before I attempted something else.
  8. F

    1951 8 N hand crank extended length

    Does anyone know of a supplier that sells an extended length hand crank? I don't want to remove my bumper. It would need to be 22" from the crankshaft end to the first 90 degree bend. Thanks
  9. F

    more starter questions

    apering the pin slightly helps and I just put one in today, I drove a tapered punch through the starter drive and stater shaft. Choose one that is close to coning out the other side. I used a small pair of vice grips held the pin next to the hole A hammer should get it started. I held the starer...
  10. F

    STARTER DRIVE

    Hobo I'm trying to disassemble a starter drive I can't get to retract, for the life of me I can't see the C clip. Any help will be appreciated Eric
  11. J

    Cockshutt 262

    Looking for information regarding 262 build. Going in a Cockshutt and seen couple posts from years ago with comments from a couple fellows. One username was stimm, other was past 40 puller. I'd like to talk with both these gentlemen if still on here or a way I could contract them. Thank you and...
  12. F

    Hydraulic intake spring 1951 8N

    Thanks for the help Harold I just ordered one plus some other things
  13. F

    Hydraulic intake spring 1951 8N

    Will do Jean Claude
  14. F

    Hydraulic intake spring 1951 8N

    I appear to have lost the #697 spring on the hydraulic pump intake valve at the bottom of the pump. It was in there when I took the pump apart. Does anyone have a source or alterative? I'm still looking keep your fingers crossed and thanks. :(
  15. F

    Home made canopy

    Do those front tires provide better flotation? Nice job on the canopy.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top