(800) 853-2651
SHOP NOW

Recent content by fireballv82003

Yesterday's Tractor Forums
  1. F

    Old John Deere Van Brunt grain drill

    This message is a reply to an archived post by Tx Jim on June 18, 2011 at 10:41:41. The original subject was Re: Old John Deere Van Brunt grain drill. Jim, Looking for a used grain feed shaft gear for an JD FB-B. Left side H320M. Know of any reasonably priced sources? THanks Mike Green Durant, OK
  2. S

    Got some catalogs

    In the mail
  3. F

    Ford 172 Diesel Timing gear whine...screech

    Bought an old 871 ford with a 172 diesel, it had a bad trans. Put a 4 speed rear on it, fired it up, ran well, only 40psi oil pressure with a really noticeable whine/screech from timing cover ( I used a stethoscope). Pulled the pan and the mains. The front an rear mains were UGLY! Reground...
  4. F

    172 diesel counterbalancer timing

    Hey all, I am an Ag Mechanics teacher at a local high school. Can anyone tell me how to time the counterbalancer when reinstalling. I have a 172 diesel on a 871 ford. Had to pull crank to have it polished and put in new bearings. Now I don't know how to time the counterbalancer when I...
  5. F

    F20 elec start flywheel ring gear

    Jeff, Did the elect start look like this?
  6. F

    F20 elec start flywheel ring gear

    The heisler kits came with a ring gear for the F20 flywheel. Anyone have any ideas about how to find out what ring gear they used? I want to make my T20 McCormick crawler elec start. The f20 bellhousing won't fit a t20. I can make a kit using a toyota starter and flexplate on the crank pulley...
  7. F

    F20 Electric Start

    Frank, I have a t20 mccormick crawler we are rebuilding in my High School Ag shop. I saw your post about the Heisler elect start kits for the F20 farmall. I want to put a flywheel ring gear on. Any idea what/where to get a ring gear for my t20 crawler? THe t20 has the same engine as the...
  8. F

    F20 Farmall - T20 Crawler Rod Bearing Shim Info

    They don't "crush" like on modern insert bearings. I realize this. They do have enough crush to keep them in place. This is determined by protusion of the bearing past the parting surface. The shim packs need to be OEM thickness so that some shims are removeable for wear - as intended by the...
  9. F

    F20 Farmall - T20 Crawler Rod Bearing Shim Info

    Hey everyone, I am getting ready to have the rods / rod bearings done for my T20 crawler. I am using undersized bearings and having their ID turned just enough to fit my crank. [color=red:934084a18d]I need some info for my machinist about shim packs for the T20 - F20 (same...
  10. F

    F20 Sleeves Pistons

    This message is a reply to an archived post by nosih on August 05, 2009 at 14:16:08. The original subject was "Re: F20 Sleeves Pistons". Do you have sleeves/pistons available how much? Thanks Mike
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top