-
F
C cultivator ?
Where can I find wedge bolts And Clamps that hold the shanks?- Five points John
- Thread
- Replies: 5
- Forum: Farmall, International & McCormick
-
F
Farmall C Hyd issue
Get it on a hill with the nose pointed down about a foot. Or jack up the rear end. That should prime it. I had to do it too. John- Five points John
- Post #1
- Forum: Farmall, International & McCormick
-
F
Finger type vs. carosel transplanter?
I Know they are used for veggies too. We use a MT brand Trans planter to set tobacco, and had a lot of trouble with it this year. I would like to up grade to a 2 row next year. What are the pro and cons of both. The neighbor has trouble getting the rows to close with his, but this may be a brand...- Five points John
- Thread
- Replies: 5
- Forum: Tractor & Farm Talk
-
F
Gleaner F3
When we farmed we had gleaners (40 years) Mostly K's and F's. They are very easy to work on. And any used combine, sooner or later you will work on. Their isn't a lot of stuff to take off to get to the trouble. I always liked the rock door and side access doors on the side When you plug up the...- Five points John
- Post #1
- Forum: Combines and Harvesters
-
F
How much $
How much would it cost to paint a farmall c. I'd just like a general idea. A friend and I was going to do it ourselves. We're not going to take it apart. It doesn't have to be show quality paint job, I just want to stop the rust. Thanks in advance John.- Five points John
- Thread
- Replies: 7
- Forum: Paint and Bodywork
-
F
Farmall c Hydraulics
OK I pulled out that set screw ? facing the right side with the spring behind it. Seems that there was a little air ( it took a second to start running oil out), Oil to there. But still no moveing. John- Five points John
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall c Hydraulics
OK where is the best place to see if the pump is getting oil?- Five points John
- Post #1
- Forum: Farmall, International & McCormick
-
F
Farmall c Hydraulics
I got a C farmall last weekend. I changed the hydraulic oil and pulled the screen out and cleaned it now it won't move the cultivator bracket. it was working ok before but was jerky and wouldn't lift if I was standing on them (175 lbs) I don't have gauges Any help would be appreciated. THANKS...- Five points John
- Thread
- Replies: 6
- Forum: Farmall, International & McCormick
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy