-
F
550
I have a 1960 550 industrial and replaced the screen this summer using metal mosquito screen. The frame was in good shape, so that made it easy. Didn't look too hard for a screen, but the little searching I did produced nothing.- FKFarmer
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
550 valve cover torque
Not sure about that...yet. I will not be able to remove the fuel tank until this weekend, and with all the grease and grime and very little clearance between the nuts and the tank, it's difficult to tell. I just happened to reach between the tank and top of the cover and could spin two of the...- FKFarmer
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
550 valve cover torque
Anyone know the torque (ft. lbs.) for the 4 nuts/bolts holding on the valve cover of a 1960 550? Just happened to be cleaning between the fuel tank and the cover and at least two were spinning freely. Any help is appreciated! Thanks.- FKFarmer
- Thread
- Replies: 2
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
550 Carb adjustment
Are you sure it is 'flooding out'? I have a 550 Industrial as well and mine was doing the same under load, but it was starving for fuel, not the other way around. Try the choke when it starts to die, if it runs better - that's your problem (in addition to needing a rebuild/clean). A friend was...- FKFarmer
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
550 hydraulic valve
Thanks for the tip - I"ve been looking for one on and off for about a year. Always seem to just miss "em. I"ll see if my luck changes. By the way, since I"m always a day late, I never know what they sell for - does anyone have a ballpark price for these? What"s reasonable? Thanks again.- FKFarmer
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
Can a 550 Industrial's hydraulic tank cause overheating?
Thanks for the reply - feel free to drop me an email. I'll snap a couple of photos and get back with you as soon as I can. Thanks again.- FKFarmer
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
F
Can a 550 Industrial's hydraulic tank cause overheating?
Looking for opinions on this one...I have a 1960 550 industrial with a front-mounted hydraulic reservoir. It's mounted with straps secured to a 'brush guard' and it sits about 2-3 inches from the front of the grill. Had problems with overheating during this season's haying (first time using this...- FKFarmer
- Thread
- Replies: 5
- Forum: Oliver, Cletrac, Co-op and Cockshutt
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy