-
F
6v to 12v conversion
Hope this is a simple question. If I change over a 6v gas vehicle/tractor to 12volt and change the fuel gauge to a 12volt, will the original fuel sending unit still work?- flatheadvff
- Thread
- Replies: 6
- Forum: Tractor & Farm Talk
-
F
GEHL 135 feed grinder parts question
You nailed it, the corn had packed behind the auger. I had a long rock bar and pushed it through. It was pretty hard and had to work at it for a little bit. Now the auger pushes in and will go past where it needs to be. I used a ratchet and socket to turn it to pull the packed corn out and...- flatheadvff
- Post #5
- Forum: Implement Alley
-
F
GEHL 135 feed grinder parts question
Thankk you for the reply. I have made the job harder than it needed to be. We used buckets to empty the bin. Me inside filling the bucket and handing it out to my coworker therough the opening at the top. That would have been a whole lot easier if I wasn't an old fart. What made me start...- flatheadvff
- Post #3
- Forum: Implement Alley
-
F
GEHL 135 feed grinder parts question
I am trying to work on a GEHL 135 feed grinder for a coworker. the input conveyor/auger front bearing is bad. I have located a parts diagram. I can see the bearing, all the mounting plates for the front, the "slip clutch" and drive sprocket, and the conveyor/auger screw. What I don't see is...- flatheadvff
- Thread
- Replies: 4
- Forum: Implement Alley
-
F
4010 diesel 24v regulator bench test
Cool. Daddy talks about using one back in his mechanic shop days. He started out in dealerships in the 50s, then started his own shop in the 60s through the early to mid 70s. This morphed into a parts store and engine machine shop. That's where I grew up, started out going with mother, she did...- flatheadvff
- Post #68
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Cool. Daddy talks about using one back in his mechanic shop days. He started out in dealerships in the 50s, then started his own shop in the 60s through the early to mid 70s. This morphed into a parts store and engine machine shop. That's where I grew up, started out going with mother, she did...- flatheadvff
- Post #67
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Thanks again for the info. I did some reading while twiddling my thumbs at work today. Found a post somewhere that a fellow gave the name for the tester for field coils. I was at work and on my phone so didn't get it saved, and don't remember the name just that it starts with an m and sounded...- flatheadvff
- Post #64
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Ok, thanks. I knew a growler is used for the armature, didn't know that was for fields also.- flatheadvff
- Post #62
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
I have one more question, in case I work on a generator again. I have read a post somewhere that mentioned testing the field coils with 110v ac. Does anyone know how that is done. I have several poppin Johnnys that I am working to restore enough to sell. I am probably going to run into some...- flatheadvff
- Post #60
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
ALRIGHT, ALRIGHT , ALLRRRIIGHHT. 😁😁😁😁😁 Finally got back to generator. New field coils, which also came with new brushes, bearings, and connection studs and insulators. Field coil screws came out easily. I could tell from previous times of being worked on that they had used a hammer and...- flatheadvff
- Post #59
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Made my 18 hour round trip last week. Was going to work on my generator this weekend, but a trailer wiring job, ie. I'm getting paid to work, came in. Also having to patch my tire as have had it patched at two tire shops, and both did bad work and still have leak. Mainly checking in to keep...- flatheadvff
- Post #58
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Thanks for the info. I found a few you tubes and read some forums that gave me some ideas of how to get it done. But again it will be a couple of weekends before I get back to it.- flatheadvff
- Post #57
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
My field coils came in a few days ago. They were advertised made in chino, but are marked made in Canada. That is encouraging. I was hoping to have this finished and have hay baled already, but that's how things go. I am now trying to get ready for a scheduled camping trip, so it will be a...- flatheadvff
- Post #55
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Reread the little information the IT manual has. The alternator is an isolated system, but does not use same regulator. Shows wire diagram for early models with generator and says alternator system wiring is similar except alternator connections. But wire diagram they show of just the...- flatheadvff
- Post #53
- Forum: John Deere
-
F
4010 diesel 24v regulator bench test
Ok, headed to Ardmore to take generator to rebuilder. Was another decision, as when I talk to them, they are rather un-forthcoming. They are the only one I know of that's left in the area. ( actually a pretty big area as they are an hour away). Tried to get a quote on how much to install new...- flatheadvff
- Post #51
- Forum: John Deere
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy