(800) 853-2651
SHOP NOW

Recent content by Gary201

  1. G

    Want input on choosing a new ute

    Curious that Honda wasn't mentioned. My wife and I just bought a Honda Pioneer 700 for farm use. We looked at all the major brands and also looked at reviews and it was an easy decision for us. 5 year warranty, no drive belts, great reviews, converts to 4 seats when necessary, and cheapest of...
  2. G

    Storing Round Bales Outside and Loss

    In SW Mississippi the figure we always used was 20%. With our humidity it depends more on bale quality. We started with a JD 410 and Vermeer 605C, and over a full season losses could be significant. Newer balers do much better. Usually the outer 2" will spoil and form a layer that protects the...
  3. G

    Oliver OC-3 crawler

    I have an OC-3 and have had the exact issue several times in the last 20 years. It was the coil in the mag every time. I changed points, condenser, plugs, wires, and checked fuel system each time. Mine was always the coil.
  4. G

    HG 42 Backfire

    My OC-3 would do this occasionally. It was the coil in the magneto every time. It would run perfectly until the first hint of a load, then start missing, backfiring, etc. Just another thing to check.
  5. G

    John Deere 555G warning light

    The most common cause of this I have seen with the G series is the transmission filter being restricted. Earlier serial number machines have the filter under the floorboard and the sensor is very sensitive. This is one of the few times I would advise using only a JD filter. Most others (Wix...
  6. G

    mystery mower

    Oops-missed the 6' part. Woods 72
  7. G

    mystery mower

    It's a Woods M-5.
  8. G

    Ford 3000 diesel help!

    Check to see if it has a thermostart installed in the intake manifold. If it malfunctions it can dump raw fuel into the intake manifold constantly. If not, the next step would be a compression test.
  9. G

    Ford 4000 (3cyl) pitman arm

    I don't think so, there is a sizable difference in hole diameter. The nut will actually bottom out on the threads before it gets tight in the taper on the one I have. I have located a used pitman arm, I should know in a few days if it works.
  10. G

    Ford 4000 (3cyl) pitman arm

    Thank you, I will see if I can find a used one for it. Thanks for the reply!
  11. G

    Ford 4000 (3cyl) pitman arm

    I am installing an aftermarket power steering kit on an early (1965-68) Ford 4000. The tractor was equipped with factory power steering with the hydraulic cylinder. We were unable to have the original cylinder repaired, and after pricing the aftermarket kit decided to go that route. I am having...
  12. G

    OC 6

    I am interested, where are you located and would you be willing to ship at my expense? Thanks.
  13. G

    Ford 4000 or 5000

    I don't have a book in front of me, but think your numbers make it a 4000. However, in 1966 if it is a 3 cylinder, it is a 2000, 3000, or 4000. 5000 has a 4 cylinder engine.
  14. G

    4000 power steering

    Thank You!
  15. G

    Duetz fahr tedder

    I don't think there is enough range of travel to make much difference, they're mainly there to fine tune the tines so they are all the same. Just my thoughts...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top