(800) 853-2651
SHOP NOW

Recent content by garytomaszewski

Yesterday's Tractor Forums
  1. G

    Buick leSabre 1994

    All kinds of bearings: alternator, power sterring, air conditioner,water pump, idler(s). Take serpentine belt off and see if noise goes away.
  2. G

    Old hay rake

    Most all older equipment had a company logo somewhere on the cast parts;gear boxes,wheel hubs.etc.
  3. G

    Case SC Ground

    The generator works either way and the regulators are "usually" marked as to voltage and polarity on the underside. Search for polarizing, it involves sparking the armature tab and battery tab of the regulator before starting the tractor.
  4. G

    Case SC Ground

    A generator doesn't know + from - that is why they must be "polarized" before starting the machine.
  5. G

    CARIGSLIST { UNBELEIVABLE}

    You might call tiger woods he may have one available soon.
  6. G

    DC3 Wiring

    There really isn't much wiring to a DC, one wire from the voltage regulator to the ammeter. That pole of the ammeter also has the feed wire for the light switch, the other pole of the ammeter connects to the battery side of the start switch, the other side of the start switch goes to the...
  7. G

    case dc

    The DC used a Case 4JMA magneto. Many Fairbanks-morse FM_ (L,J,X) models will also work.
  8. G

    JD B E85

    What MSD says plus you MAY have to open the load and idle needles some. I'm not sure if the gas/distillate carb had bigger jets or smaler ones, but you will need a little tweaking with the needles to get peak performance.
  9. G

    Farmall F-20

    These were a throttle control before someone "updated" the governor. If you look at the front of the tube from the carb there shoud be a lever with a hole in it that used to be the throttle control. Tom, all my shutter controls were mounted on the gas tank brackets, one side had manifold heat...
  10. G

    Case 730 stops moving after 500 feet

    So exactly why is it THAT DARN CASEOMATIC when the operator doesn't know where to do a basic first step of checking all the fluids before starting the tractor, car, truck ???? Some of us have been using COMs for 50 years without any problems, of course we did read the manual (the book that...
  11. G

    identify JD mower?

    jdman, disagree a little, the breakaway is still there, have a couple mounted the same way to Case eagle hitch.
  12. G

    haybaling costs?????

    Wow, dave; 20-25 pound bales ? Is that a norm ? We usually go 60+ or some of the little horsey girls wanted max 40 pounders.
  13. G

    JD semi-mount one row corn picker

    That would be a model 101. Rare ? Maybe, they are over 50 years old and many have been junked by now. They were okay for the corn of the era. The implement photos section here has a couple of photos of an unrestored one.
  14. G

    O/T my new truck

    Nancy, Talk to your local trucker performance buds, they can probably tell you what a minimum pressure would be for those shocks. I'm thinking 15-20 lbs and up it if loaded. On board compressor ?? That's a 1 ton and will never ride like a 1/2 ton or even as smooth as a 3/4.
  15. G

    distinguishing sides on farmall

    Unless it is a 2 cylinder Deere.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top