(800) 853-2651
SHOP NOW

Recent content by gene g

Yesterday's Tractor Forums
  1. G

    4020 help reconnecting trans to clutch housing

    Dont use the bolts . try putting a chain from rear axle to front axle .Now stand on chain this will pull tractor together and not damage clutch or transmission . Last guy I saw who used the bolts when he was done I replaced his transmission case .$$$$$ You could check clutch disc maybe in wrong...
  2. G

    JD 350 crawler injector pump replacement

    If its the square packing in the nut that screws on to return line tee you will need to go to deere
  3. G

    remote receptacle won't release

    Shut engine off turn breakaway on , now move scv lever back and forward to relieve oil pressure now turn breakaway off . If you still cannot remove hose reach in front of breakaway and pull or tap receptacle to the rear . If the ball bearings are rusted into the receptacle try pulling on the...
  4. G

    1020 hydraulic issues

    Some times you can see a mark on the end of the lines at the trans. end where the keeper was holding them into the case .
  5. G

    1020 hydraulic issues

    I dont know which line goes where . But some small utility tractors had a check ball in one line . A parts book would answer what models used the check ball
  6. G

    1020 hydraulic issues

    The reason I ask is because I had a remanufactured valve do the one way creep and I found the problem in the lower part of the housing . Im sorry I cant give the exact detail on the repair . I do not remember its been several years ago . I remember that I had to remove the entire valve to...
  7. G

    1020 hydraulic issues

    SORRY I said open center pump my mistake I should have said closed center pump . My mistake my proof reading needs some help.
  8. G

    4010 JD hydraulics kills tractor ?

    Trolling ? new word for me ?
  9. G

    4010 JD hydraulics kills tractor ?

    You should not be able to kill the engine with a closed center pump . This is going to be a good one . You have checked standby its correct .When you demand flow the power needed will increase but not enough to kill engine.This problem started when the new loader was installed correct ? Have you...
  10. G

    1020 hydraulic issues

    You can put the gauge directly on out put end of an open center pump . The pump will destroke and stop pumping when it hits standby pressure . You can then adjust to correct pressure . Then reconnect pressure line. If pressure drops you know you have an internal leak on the high pressure...
  11. G

    1020 hydraulic issues

    Mark If you are using the line in the picture it would probably be a good idea to replace it or repair it . I have not tryed to replace it with a rubber hose, it mite be possible . I was always told repair all known problems first . Did you look at suction screen , and replace hyd filter...
  12. G

    1020 hydraulic issues

    If the hose in the white bucket is coming out of the filter housing , through loader valve and pumping oil into into bucket this will rob return circuit of oil needed to supply main front pump and reduce out put . It can be plugged for testing purposes .
  13. G

    1020 hydraulic issues

    Sounds like loader maybe plumbed in front of priority valve like Jim and JDEM said this will rob the system of more oil than the pump can create .I dont have the exact pressure for priority on this model but it should be around 1700 psi .If pressure is below this it can cause your steering...
  14. G

    4020 Power Shift Issue

    The power shift diagnostic is done with a gauge bar that hooks to all clutch packs and brake packs at the same time . With out this tool to give you pressures in real time you can have a very difficult time finding problems . If you can get a gauge bar its not hard to find problems . the service...
  15. G

    Deere 2555 scv teardown tips

    I have been told that its possible to back return valves off 1/8 turn and pressures valves off 1/4 and not use dial indicator I have never used this method . If it would work it may be helpful for peps without dial indicators .
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top