(800) 853-2651
SHOP NOW

Recent content by gene1605

Yesterday's Tractor Forums
  1. K

    Lifting engine points on Tea20 standard motor

    Hi Am about ready to put motor back to Tractor and wanted to know if there was a correct way or lifting points. Thanks
  2. M

    blasting cabinet

    I am looking for a blasting cabinet. I don't want a cheap unit but don't want to break the bank, either. I am familiar with the Skat Blast cabinets and want something like that or better. Any suggestions? Thanks. Mike
  3. M

    Hydraulic seat accumulator adapter

    Hello All I was curious if any one had an extra hydraulic seat accumulator adapter, p/n 15-150-1, I am currently working on a 1456 hyd seat, I would like to recharge the accumulator but cant seem to find an adapter. Thanks to any responce. MM
  4. 8

    1949 JD A carburetor nozzle removal

    What is the best way to remove the main nozzle on a JD A tractor from 1949 ? I f I remember right they use to be removed by using a small slide hammer puller, but also looking for other ideas and will I need to replace the old one after I remove it ?
  5. M

    600 ford

    Can some one tell me if a Ford 600 will travel slow enough to run a tiller behind it? I am not sure what speeds they run or what speeds it needs to operate a tiller other than a slow speed. Does it have a high and low or is it like an 8n 4 speed? Thanks Floyd
  6. S

    Ford N wiring

    Hello I am hoping someone can help me or possibly (JMOR). I bought a ford 9n maybe it's a 2n or 8n I was told it was a 9n but not 100% sure. I followed a guy by the user name JMOR from this site and used his wiring diagram and when I hooked up the 12v battery and turned on the key and the wires...
  7. A

    Cub cadet lift assembly

    I have an older cub cadet 2050055u541797 which unless I'm mistaken is a 1000. I'm trying to find information for mounting a harvester international tiller on it. I believe it's called an a-1?
  8. R

    jd 214ws not tying

    We got the timing- baled a bunch last night - lost idler gear on auger- replaced- baled more- started missing bales - got down to only 2 left- wire not threading or staying threaded part of the time. one side will tie and other side no wire- switches back and forth- found a loose pin in twister...
  9. 5

    Re Park brake

    I finally found out what the problem was with my park brake on my 1999 3500 Dodge. The park brake pedal itself was broken. I found more info on the web about this problem. Apparently it is a somewhat known problem. But the bad news is a 98 and 99 maybe 00? are the same. Found plenty of 94...
  10. K

    IH 504 Power Steering

    I have a 1966 504 with power steering and it leaks hyd. fluid where the power steering cylinder, piston arm joins to to the small block that the 2 hoses mount onto. Is there a O ring in there and does the piston shaft thread into that little block ??
  11. M

    Setting JD 55 for wheat

    I think this may be the year the 55eb finally gets put to work in some wheat that the neighbor has. Main question is what should my cylinder speed be? Currently it is at 619rpm and the manual has a rather wide range of settings for it and well changing sprockets is not as easy as a variable...
  12. T

    8N steering housing

    I'm in the process of rebuilding my steering housing on my 8N 1950 model. It has the newer housing for 1950-1952 units. ok, so does anyone know where i can get a manual with good instructions so I can get it back together correctly. I'm replacing the seals and all gaskets. Thanks in...
  13. C

    ford 600 three point hitch issue

    I'm having trouble with the three point hitch on my ford 650. the blade wont lift until I drive the tractor around first. then I can reattach the blade and all is well. Checked the hydraulic fluid and the levels look good. Where do I start?
  14. A

    Welding Helmet Lens #?

    For those who pay attention, what lens shade # do you use to weld? Most of what I do is with 1/8" or slightly bigger rod running under 150 amps on a tombstone. The lens in my helmet now is so dark I can hardly see the arc and can't come close to seeing the seam I'm trying to weld. Some charts...
  15. K

    Red Power Roundup in Racine Wis.

    Is anyone going? Is anyone from here there? What is the show like and how are the grounds?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top