Recent content by Gieryic

  1. G

    John Deere 1010 R seat cushions

    No match at shoup No match at Steiner Any other constructive thoughts Thanks
  2. G

    John Deere 1010 R seat cushions

    Did anyone find a replacement seat set? I have the same seat and can’t identify a replacement Thanks
  3. G

    276 hay liner failing to knot the number 2 twine

    It wasnt to bad but I paid special attention to the washer locations..
  4. G

    276 hay liner failing to knot the number 2 twine

    Well - it spins but has a pretty nice flat spot on it
  5. G

    276 hay liner failing to knot the number 2 twine

    Final post on this topic as the problem is solved The root cause was a sheared woodruff keep on the Tucker finger cam (located on the knotter drive bar. To get to it I partially disassembled the knotter stack from the left side - removed the drive chain, knotter clutch and cam, and...
  6. G

    276 hay liner failing to knot the number 2 twine

    The plot thickens Yes, a slight bend in the twine finger bar wasnt the cause We found the woodruff key that drives the twine finger cam had sheared. It would rotate intermittently that was quite confusing $0.85 part at the hardware store. More to follow tomorrow
  7. G

    276 hay liner failing to knot the number 2 twine

    So, I believe I found the issue (and I feel like a dope). There is a slight bend in the twine finger lever bar.. Ive straightened it and will test it out I honestly dont know why or how it occurred or how we were able to get the first cut in the barn but this year but here we are Ill update...
  8. G

    276 hay liner failing to knot the number 2 twine

    Ill get someone to help Me roll it through a cycle tomorrow One question- twine finger timing or beyond that? Ive read the repeated posts to start with the needles, etc, etc. Im afraid to change anything. Thanks
  9. G

    276 hay liner failing to knot the number 2 twine

    I dont believe either are broken as the number one twine on both sides have perfect knots. They just arent tied with the number two twines. In short, I get a perfect bale with two sisal twine with a knot on one end To that tells me the billhooks are spinning and the wiper arms are pushing the...
  10. G

    276 hay liner failing to knot the number 2 twine

    Help My 276 hay liner is failing to knot the number two twine on both knotters Ive read the manual and will check the twine (Tucker) finger timing and the distance to the needles but the fact that the identical problem on both bail twines has me skeptical. Any guidance (or reassurance)...
  11. G

    Jd 2840 pto control valve springs

    Forgive the perhaps stupid question..... Can I complete this without dumping the hydraulic system contents? I was about to change the hyd oil and clean the suction strainer but stopped myself.....hy-guard is n0t cheap....
  12. G

    Jd 2840 pto control valve springs

    Thanks. Thats where I was going...
  13. G

    Jd 2840 pto control valve springs

    Right side of tractor not left Orange knob not rod
  14. G

    Jd 2840 pto control valve springs

    A couple of corrections: Orange knob, not rod Valve located on right side of tractor (under right foot) not left Sorry
  15. G

    Jd 2840 pto control valve springs

    The attached photos are not in order The black shaft with orange rod is the engage/disengage. Up to engage - shown disengaged The green vertical rod with the jog in it is below the operating platform looking back on the left side of the tractor if you were sitting on it. The vertical...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top