(800) 853-2651
SHOP NOW

Recent content by Glenn D

Yesterday's Tractor Forums
  1. G

    Geared sarter

    Well I cleaned it up and replaced the jumper wire and terminals..I used a heavier wire. I put the old jumper on and it works now. The wire is too small and must be just enough resistance to pop out the bendix before the starter turns...complete fluke. So the little wire is carrying the current...
  2. G

    Geared sarter

    I have a 9, 2 and 8n tractors. The 2n needed a ring gear and I ended up putting a geared starter and it and it worked like that without issues. We moved and I had to park it for a couple years. with those geared starters there was a gotcha as it has seperate terminals for the solenoid and...
  3. G

    Sherman from the mud

    I guess the only way to tell if this is a step-up/down is by original colour of the unit?
  4. G

    Sherman from the mud

    Hi Joe, heres a few photos. I didn't mention that it's still in the tranny case
  5. G

    Sherman from the mud

    Sure I can.. ugly though. lemme get em and post back. I'm in Nova Scotia. Mostly Fergies around here This post was edited by Glenn D on 10/02/2021 at 03:34 pm.
  6. G

    Sherman from the mud

    So I have a 9n 2n and 8n, my 9N alrerady has a Sherman on it (step-up) but it came with another one that had sunk in the mud and is pretty rusty. I'm sure it could be brought back with all new .. well everything. I've had it a long time and don't see ever needing it but I don't know if I should...
  7. G

    Not a tractor but..

    Just the info I was looking for. So the engine had an old jacket draped over it instead of an air cleaner I'm assuming it's not an OEM jacket and I dont see a metal air cleaner anywhere so ill have to find something I can use that has a filter.
  8. G

    Not a tractor but..

    Thanks for your help everyone. Runs like a top now still needs 2nd oil change. wires, plugs.. points and cap seem ok. Went with the electric replacement pump. Mechanical one was too far away . Valve train is a little noisey but I'll run it a few more times it's not that noiseybthatbibwould...
  9. G

    Not a tractor but..

    Got it running but the fuels pumps don't work so ill see about getting one in tomorrow. I'll put the mechanical back on it if I can get one instead of the electric.
  10. G

    Not a tractor but..

    Yup the original pumps there but disconnected. The ignition switch is acc to the left, stop in the middle and run/start to the right so the pump came on a few seconds after the battery hooked up abdxsurprised us. Trying to get spark now probably be running shortly unless the coil is bad I don't...
  11. G

    Not a tractor but..

  12. G

    Not a tractor but..

    Here is a photo of the Id boss on the side of the engine.
  13. G

    Not a tractor but..

    That explains it heh.
  14. G

    Not a tractor but..

    I'll have a look I'm headed out there shortly we are going to to get it going. Not really sure how its getting gas. There is a gas tank there probably from the truck but its below the carb and seems to bypass the fuel pump. Seems like it should be gravity fed. This photo shows the only thing in...
  15. G

    Not a tractor but..

    Saw mill actually. Thanks for the tips, i knew I'd find out here. Where on the block will the id markings be? It looks to be a 50-52 silver diamond but not sure how to tell what size. Thanks everyone
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top