(800) 853-2651
SHOP NOW

Recent content by gmcdeadhead

Yesterday's Tractor Forums
  1. G

    Pertronix ignition upgrade for IH 444 Gas

    exactly correct
  2. G

    Pertronix ignition upgrade for IH 444 Gas

    300 GUY , you went 12 years with no problems, I think that's pretty good , buy another one for the tractor and it will be good for another 12 years ,I have them in all my tractors and they all start right up on a dime ,
  3. G

    Pertronix ignition upgrade for IH 444 Gas

  4. G

    International 574 new power steering pump. Lines dont fit?

    id send the pump out some where to get rebuilt if there isn't a place nearby, who cares if it exceeds the price of a new one , at least it will go back in with no modifications of the lines ,
  5. G

    Need GOOD spark plug wires to use with Pertronix electronic ignition (Farmall Super M)

    mike1972chev, I've been buying suppresison wires off of rock auto for years , there real cheap to , I get the ones for a Chevy big block motor , so I can get two sets of wires out off the set that I bought , I just get some extra boots and ends, don't waste your money from brillman, not saying...
  6. G

    Drill press

    im always looking on market place for good deals , like I said before, it hard to pass up a nice American made drill press for cheap , the chucks and motors are worth money also
  7. G

    Drill press

    I see a lot of good deals on marketplace, but how many can you have , I have two now that I use , and if I would have bought all the good deals it would be up to 10
  8. G

    Gresa gun..

    yep , same thing here , leaks, messy
  9. G

    LED shop lights

    these are the best bang for the buck , I have 10 in my 24'x40' shop and they work good , Maxlite LSS2XT8USE4803 2-Lamp T8 LED Tube Ready 4ft Linear Utility Pre-Wired Strip Light Housing:
  10. G

    Old Metal Lathe

    unless someone is looking for parts for another exact lathe like that , its probably only worth scrap price , anyone looking to get into machining would start out with a better shape lathe with more tooling for around $400-$1000
  11. G

    Drill press

    I would go on marketplace and look for an used 1970-1990 sears craftsman 15-1/2 floor drill press, american made , good quality , and anywhere in price from $75-$200 , depending on condition , most of the time people are just looking to get rid of stuff, there moving , or just that they don't...
  12. G

    Log splitter table

    heres mine that I welded and put on my splitter , its removable so I can take them off if needed
  13. G

    Can I brag??

    I also have the pertronix in my W4 and my IH 504 , best ever starting , a few rotations of the motor and they fire right up.
  14. G

    Carb cleaner

    soak it in a bucket of gas
  15. G

    Gasket set question....

    yes , thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top