(800) 853-2651
SHOP NOW

Recent content by gmoose

Yesterday's Tractor Forums
  1. G

    8N hydraulic oil

    I appreciate the replies
  2. G

    8N hydraulic oil

    I used CARQUEST 80W 90 gear oil GL-5 in my 8N but it seems to foam a little. Did I use the wrong oil. thanks
  3. G

    8N hydraulic oil

    I used CARQUEST 80W-90 gear oil GL-5 and it seems to foam a little. Is this oil ok for the 8N. thanks
  4. G

    Control arm on 8N

    Lift does not change with position control lever in either position
  5. G

    Control arm on 8N

    Is control arm perfectly straight? Mine has a slight bend. I have no lift control until touch control lever gets about 2 inches from top and at about 3/4 inch wants to go all the way up and no draft control at all. thanks
  6. G

    8 N Hydraulic lift

    Thank you very much Bruce
  7. G

    8 N Hydraulic lift

    JMOR , that's a lot for my little brain but I'll sure try to understand it, thank you very much
  8. G

    8 N Hydraulic lift

    What exactly does this jig help adjust as I have a hard time imagining how, thanks
  9. G

    8 N Hydraulic lift

    I have been using the position control lever in vertical position for position control, when I put it in draft position, fully forward, it does not seem to make any difference. Lift cover spring adjustments were according to manual but I was not able to get valve rocker lever to contact pump...
  10. G

    8 N Hydraulic lift

    Yes Pin was replaced, thanks
  11. G

    8 N Hydraulic lift

    The rear blade on my 8N will not lift until I get Touch control lever about 1- 1 1/4 inches from top and then I have no control as it lifts all the way up at once. I replaced all parts in pump and had lift cover off and replaced cylinder and piston along with pin for position control arm. please...
  12. G

    8N Lift , Quadrant

    For some reasons my comments on my post are not in order, which makes this confusing to some including me, sorry
  13. G

    8N Lift , Quadrant

    I had lift cover off to replace ram cylinder and piston to fix leak and also replaced pin. I checked internal adjustments according to manual at that time and could not find anything. I also had pump out and replaced parts. Will have to take lift cover back off and recheck, thanks
  14. G

    8N Lift , Quadrant

    As I stated in my post I have tried adjusting Quadrant according to Manual and no matter where I move it 3/8 to 1/2 inch is as close as I can get rocker lever to pump housing, that"s with touch control lever up and the 4 bolts loose on quadrant, thanks
  15. G

    8N Lift , Quadrant

    I cannot get rocker lever [intake valve] to contact pump housing when control lever is all the way up when I try to adjust Quadrant according to FO-4 manual. Control lever has to be about one and one half inches from top before lift comes up. Lift does go all the way up at this point. Intake...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top