(800) 853-2651
SHOP NOW

Recent content by go mo

Yesterday's Tractor Forums
  1. G

    Hyd clutch adjust on vista

    You need to eliminate the acuator as well and loop the pressure line back to the return line.
  2. G

    Hyd clutch adjust on vista

    Your best bet is to eliminate it. The clutch doesnt push that hard any way.
  3. G

    Vista 3 spd fwa

    There were just two built one with a cab and one without. I dont remember which one you got but I remember washing it up for the auction where Jack bought it.
  4. G

    Stuck oil pan

    I watch the other guy hug the heater and wait for the ice to melt.
  5. G

    Stuck oil pan

    Massy 97 doesent have the filter in the pan or the adjusment in the side of the pan. I usually throw a couple of tires on the ground under the tractor make sure all the bolts are out and smack it on the sump with a sledge. Have taken off literlly hundreds this way and never damaged one yet.
  6. G

    WHAT THE DIFFERENCE BETWEEN GBD GTBD ?

    bull gears and bull pinions are differnt between a G and a GB. G is 15 and 60 GB are 14 and 61.
  7. G

    MM 220 Max Bore: Courtesy LW

    Sounds like he is getting tired of the same ? Maybe you ought to write it down
  8. G

    White 2-150

    Is there a phone #? Southern Ill is a big place
  9. G

    gb engine in uts

    Just grind out the bell housing and run the GB ring gear and starter. Sometimes the GB flywheel will hit the back of the clutch housing you can either turn it down in a lathe or get a later U flywheel from a 12 volt tractor and the GB ring gear will interchange with it. The 6 volt u flywheel...
  10. G

    Heading to Oakley, MI big MM show?

    Do they pull any heavy farm stock type classes? Might bring up the Vista ifthey have a 11,000 or 12,000 pound class.
  11. G

    reproduction heads?

    The head is nothing like a stock head. Thicker decks and ports and a huge boss for the valve guide so you can move the valves around wherever you want and yes I have seen them.
  12. G

    G1000 Vista hubs

    vista has a larger axle than a G900 or G1000. It is the same as a G1050.
  13. G

    Removing name plates or side rails

    I used an acetylene torch with the flame set very light in other words just enough ox to make it burn without smoking. I started at one end and just moved back and forth till it started to come loose. Once you get started you just keep following it down till the piece comes off. I did practice...
  14. G

    GB puller

    That is pretty much standard issue now days.
  15. G

    Removing name plates or side rails

    yes the trick is to drill out the rivets on the name plates and remove the ones on the black strip by tapping them out from behind. Then with someone to help use a long thin piece of steel to slide behind the piece while someone heats the inside of the hood. The heat will release the glue they...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top