(800) 853-2651
SHOP NOW

Recent content by gregarpp

Yesterday's Tractor Forums
  1. G

    TO-35 replace center link with hydraulic cylinder?

    I don't have any hydraulic ports on my tractor. I do have a 2 spool valve. I would only need a single spool for this?
  2. G

    TO-35 replace center link with hydraulic cylinder?

    Anyone do this? It is getting old constantly adjusting the 3 point centerlink on my drag bucket.
  3. G

    parts

    I tried to buy from them twice, never got anything shipped. I would avoid them!
  4. G

    To-35 1955 clutch update and leaking oil pressure line

    Put the tractor back together this morning. Took one try, everything lined up and went together. Took if for a test run today, I can now actually feel both stages of the clutch. I now have a leak in the oil line to my gauge - it is rotted. Can I change the line or do I need the gauge also?
  5. G

    To-35 Oil Pump to Cap - Shim or Gasket?

    John, I think you are referring to the cover plate gasket, which I have. I looking at how the entire oil pump mounts to the engine. My booklet shows a shim. I have no shim nor gasket, is this normal.
  6. G

    To-35 Oil Pump to Cap - Shim or Gasket?

    When I pulled mine off the tractor there was no shim or gasket. When I reinstall I don't need a gasket or anything? Just bolted it and torque down? What type of wire for the bolts, or are people not re-wiring them?
  7. G

    1955 TO-35 Flywheel fit clearance? And input shaft clearanc

    Nothing in particular. Never did this type of work before and don't wanna do the same job twice!
  8. G

    1955 TO-35 Flywheel fit clearance? And input shaft clearanc

  9. G

    1955 TO-35 Flywheel fit clearance? And input shaft clearanc

  10. G

    1955 TO-35 Flywheel fit clearance? And input shaft clearanc

    Some photos of my flywheel installed today. Does the gap on the flywheel/engine look normal? Does the remaining spline on the input shaft look normal?
  11. G

    Rope packing for rear main seal

    I am showing 2 part numbers for a 1955 TO-35 1006635M1 1021673M1 I would hate to order something online that has shipping twice the cost of the item! Or can I just purchase some cotton rope to use? What size diameter?
  12. G

    Still cannot removeinput shaft from TO-35

    This is a 1955 model. I got it today. One more snap ring behind the thrust washer. Now I am working on removing the seals from the input shaft. I got the large one. Not sure how the small one will come out.
  13. G

    Still cannot removeinput shaft from TO-35

    I have read the instructions from John UK. I have the PTO cover plate, 2 snap rings, bearing and bearing retainer removed from the tractor - finally. The input shaft and housing can only come out 1/2" or so. I am trying to pull the PTO shaft forward, I get about 1/2" I can push it back...
  14. G

    TO-35 removing input shaft housing to replace seals

    1955 To-35 with dual clutch. I want to change the transmissions seals since I have the tractor split. I see that I need to pull the lower PTO shaft forward in order to remove the top input shaft/housing. I cannot pull the PTO shaft forward, and the PTO bearing housing wont move either...
  15. G

    TO-35 1955 Clutch, oil pump and seals

    There is a cork plug in my flywheel. What should I do with this?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top