(800) 853-2651
SHOP NOW

Recent content by grinder220

Yesterday's Tractor Forums
  1. G

    Allie-chalmers electric motor

    There wasn't much that Allis didn't build, that was part of their downfall. Way to many coals in the fire but the electric division was actually the last to go in I believe 2012.
  2. G

    GVI with inline pump using Case parts?

    Got any pictures, I'd like to see that.
  3. G

    Found a MM G1000 Sitting in Someone's Yard Going to Pot

    Good to know,I've been looking for a diesel brown belly for a little while now just because I like the 2 tone paint over solid yellow. I would imagine if they had bearing problems they would have been taken care of by now, well hopefully.
  4. G

    Found a MM G1000 Sitting in Someone's Yard Going to Pot

    what problems did the early G1000 rear ends have? I wasn't aware of any on those models
  5. G

    Found a MM G1000 Sitting in Someone's Yard Going to Pot

    Looks like an earlier brown belly model. $6000 is a little much in my opinion, especially if its been sitting that long without ever being ran. Probably gonna need some work to get it running again. Is it diesel?
  6. G

    Found a MM G1000 Sitting in Someone's Yard Going to Pot

    VISTA has a raised platform, shorter hood, fuel tank behind seat like the 210 has and shifter, throttle and hydraulic controls of to the right on a console.
  7. G

    426D in a D17

    Looks good. What was required to attach it to the bellhousing and input shaft?
  8. G

    obsolete gasket needed

    Thanks for looking, if I can't come up with one by the weekend I'll probably use some RTV or something . Making that gasket is not something I want to do, lol. To many holes and not enough patience.
  9. G

    obsolete gasket needed

    Still looking for a gasket, hoping to get it together this weekend.
  10. G

    obsolete gasket needed

    Yeah I got it apart, cracked it good on the end with a sledge hammer and it started to come free, the gasket was all that was holding it, no dowl pins at all on it. Now I'm fighting with getting the outer bearing and the sleeve of the axle shaft without ruining anything . Is it safe to heat...
  11. G

    obsolete gasket needed

    Anyone know where I can find the gasket that goes between the rear axle housing and rear end on a G705? Acgo no longer has them.
  12. G

    New to Fourm and New Combine

    So what size Gleaner is that 101 comparable to? What does it have for an engine?
  13. G

    New to Fourm and New Combine

    I was going to send you a private message but it looks like its disabled. Here's my email [email protected] , if he still has it I wouldn't mind looking at it.
  14. G

    New to Fourm and New Combine

    Bill, I'm from east central Iowa. How much is Gleaner?
  15. G

    New to Fourm and New Combine

    Very cool find. I've always liked the looks of the older IH combines. I also run gleaners but would like to find a 503 IH. We used to own one when I was young then we bought a gleaner G, another combine I'd like to find.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top