(800) 853-2651
SHOP NOW

Recent content by griz50

Yesterday's Tractor Forums
  1. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    By bottom shaft you mean the differential drive shaft in the transmission? Sounds like a good offer, I need to change out everything with the different case, I'm also expecting to find bearings to replace, seals, and possible other parts as well.
  2. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    OK Tim, I'll use your post to reply giving you and everyone else the tally in $$$$ on a used inspected and cleaned case, $850, and I pick it up. I was also told salvage people sell a lot of these for pulling tractors.
  3. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    Yes Mark and thank you for that response
  4. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    Yes Tim that scares me, but I was expecting that the more I find out here and inspect that wreakage. I'm checking on salvage cases right now. I guess to write this off and find something positive it is that others who visit here will see what happens when you do something wrong like what we...
  5. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    OK Bob this is all finally, wasn't sure what I was doing with those uploads, sent some to myself here. Oh well I hope everyone can see what happened.
  6. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

  7. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    ]http://forums.yesterdaystractors.com/photos/17145.jpg[/img] [img
  8. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    Having trouble with uploading the pics, do you see any of mine at all?
  9. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    Yes Bob I totally understand that now, you also scared me. Just kidding. May I ask, even though it's been 15 years, how much did that 3020's cast housing set him back? Any ways I have some pics I'll try to upload of my disaster. I used an old Kodak easyshare, but I think they'll show what you...
  10. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    I'll use this reply to first thank Tim and Jim for their response. To you Bob this is amazing you'd suggest that possibility, because I was about to ask that very exact thing. And yes there was a clutch job done, and yes bell housing bolts were used lightly, the shaft and splines were lined up...
  11. G

    '63 4010D trans/hyd pump broken bolts&damaged casting

    I'd like to give a description first to see if any of you JD gurus or owners have encountered same situation as me, and perhaps shed some light. It started with some seemingly mild shifting problems, 8th, 7th, 5th, & 3rd gears would almost engage with some gear chatter, but no further. To...
  12. G

    4010 D injector line leaks

    Yes Tim, after going through this some local mechanics have said they are a problem, can be tricky ect. But I guess after cleaning them retightening and whatever else they tend to stop leaking. I even loosened some bolts on the high pressure fittings after leaks were stopped to purge air and...
  13. G

    4010 D injector line leaks

    I finally solved the leak problem. The tip from msb about cleaning those banjo fittings in paint thinner then blowing them dry helped a lot also tightening them a little more. What else I"d like to share is, the low pressure banjo fittings on the return line on top of the injectors was also...
  14. G

    4010 D injector line leaks

    Thanks msb & Allan for your responses. I haven't yet worked on the 4010 yet, been busy this weekend. I would ask msb now, if by loosening the injector clamps, and the return line hollow bolts first, enough to allow for free movement, then loosen the banjo fittings far enough to drain fuel, will...
  15. G

    4010 D injector line leaks

    Thanks to the many posts here from you JD gurus and the JD Roosa Master manual I was able to disassemble, clean, and install a seal kit for my 4010 DB injector pump. I finally got it all back together today and after a little starter cranking it fired and seems to run quite well also starts...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top