Recent content by GSW

  1. G

    Ferguson TEA-2085 restored back to life

    Can I ask ,,I know this is an old thread,but did it take a long time to adjust it and then does it run rough till warmed up?
  2. G

    Still having problems with the TEA 20 zenith 24 t carb/

    Ok. Will do. I started the old tea 20 today,started without choke,but it wasn't cold outside. Just one click. It ran rough for about 5 min,then started clearing up,abd ran pretty darn good. I drove up through whe woods ,and it never stumbled. Idles down to almost nothing and dosnt stall. Im...
  3. G

    Still having problems with the TEA 20 zenith 24 t carb/

    I cant seem to find that post you were talking about
  4. G

    Still having problems with the TEA 20 zenith 24 t carb/

    Well I thank you for the info. I checked my points yesterday. The shaft as a very small amount of play....new points though I adjusted the carb,,a bugger to get right....abd got it to work pretty darn good. Took it in the woods over cradle hills,wasn't too bad. Today..I started it up,no...
  5. G

    Still having problems with the TEA 20 zenith 24 t carb/

    I plan on taking the carb apart again. When I first opened the carb,when I got the tractor and it started acting up afrer a few days..,someone had two washers on the needke,worked when I got it,for a few days,then all thos happened. Like I said before..I did a stupid thing by pouring a tiny bit...
  6. G

    Still having problems with the TEA 20 zenith 24 t carb/

    Yup. I tap the float. But I still have to adjust it . I never knew these fergies were so troublesome. Well....back to opening tge carb..again! Btw are two washer ok under the needle?
  7. G

    Still having problems with the TEA 20 zenith 24 t carb/

    When i purchased this tractor,and got it home,it ran like a champ.I got a stupid idea to put a tablespoon of seafoam in the tank.A couple days later ,the tractor was not working right.It was serching,like starved for gas.I could fiddle and adjust the carb,get it idling and working for a half...
  8. G

    tea 20 zenith 24 t carb and needle and seat

    I just installed a carb kit in the old tea 20.When i opened the carb,i seen that there were two washers under the needle and seat.I put the new needle and set in (which was a bit different on the needle.The needle was skinner than the old one) same length,,but skinnier. .I installed the two...
  9. G

    Is this butterfly and shaft too loose?

    Seems like the kit s new butterfly and shaft was bigger. Had to sand down shaft to get it to fit.
  10. G

    Is this butterfly and shaft too loose?

    The kit had those...but they wouldn't fit. The new shaft was tight enough that now its good.
  11. G

    Is this butterfly and shaft too loose?

    Ok. I installed a new butterfly and shaft,on carb,and it was nice and tight,compared to the old one. Still turns easily,, Installing carb tomorow..
  12. G

    Is this butterfly and shaft too loose?

    Can't download vid
  13. G

    Is this butterfly and shaft too loose?

    Putting a carb kit in the tea 20 ,zenith carb. I noticed the butterfly shaft is a bit loose. I have sent video. Its hard to see,but maybe you all can let me know,by seeing. The tractir was hard to adjust..thought a new kit wold do. Im just going to wait to see what you allsat,before putting a...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top