(800) 853-2651
SHOP NOW

Recent content by gulag1

Yesterday's Tractor Forums
  1. G

    Hitch for Allis Chalmers WD45

    Thanks, Jim.ME! Sure looks the same. I'm over the pond until the 1st but will will get a look as soon as I get back. It is so much easier to understand this stuff with good pics / videos.
  2. G

    Hitch for Allis Chalmers WD45

    Thanks, 4wd. Heading out of town for the week then back to the WD45 puzzle. One thing I know for sure is that I'm missing some screws and bolts so I'll have to think about that as well.
  3. G

    Hitch for Allis Chalmers WD45

    Thanks. Trying to figure out where the supports attach to the tractor. I see where the left and right brackets on the guide should attach (I think) but not the supports on the portion with the block.
  4. G

    Hitch for Allis Chalmers WD45

    Ok - hydraulics problem solved so now I'm removing the belly mower and reattaching the drawbars. Having trouble understanding where the supports on the block attach on the bottom of the 45. I looked for screw holes that would match up with those on the block supports but didn't see anything.
  5. G

    Hitch for Allis Chalmers WD45

    Speaking of feeling stupid.....now I feel really stupid. Went out to look at all the screws again and noticed that screw B, even though fully screwed out, wasn't not holding the plates together tightly. Rigged it so they held together firmly and voila, working perfectly now. All that effort...
  6. G

    Hitch for Allis Chalmers WD45

    Got it. Thanks. Going to try a few more adjustments then its probably time to get into the pump itself.
  7. G

    Hitch for Allis Chalmers WD45

    Yep, that's the way it should work. I'm just curious about what is actually happening in the mechanics of the pump. Since the hand lever doesn't raise or lower anything (I can only get it to lower and stay lowered by pushing the control lever by hand CCW then screwing the pin into the divot...
  8. G

    Hitch for Allis Chalmers WD45

    Does anyone know where I might find a diagram of the inside of the pump and how the hand lever interfaces with its ability to pump oil? I know a little bit about hydraulic dynamics so does the hand lever act as the control valve to regulate the amount of fluid? Thus at 1/2 raised on the hand...
  9. G

    Hitch for Allis Chalmers WD45

    DrAllis. I stand corrected. It was not correctly in the divot and once I got it there, everything stayed lowered. Now I just need to get the pump working correctly so its not stuck in raised or stuck in lowered with no way to adjust via the hand lever.
  10. G

    Hitch for Allis Chalmers WD45

    I do have to push it CCW past the divot to get it to go down. I then screw it into the divot, but as soon as I fire her up, belly mower goes to the fully raised position.
  11. G

    Hitch for Allis Chalmers WD45

  12. G

    Hitch for Allis Chalmers WD45

    I will look again, but unless there are two divots, it is in the one divot screwed tight. I'll do it again and take a picture.
  13. G

    Hitch for Allis Chalmers WD45

    Thanks! Did that one already. Still goes to raised position. I'm not a surgeon, but it just seems logical that there is something disconnected / broken in the housing body.
  14. G

    Hitch for Allis Chalmers WD45

    If your talking about this one, yep + just installed a new one.
  15. G

    Hitch for Allis Chalmers WD45

    Thanks, 4wdtom. I will try to see if I can push them down. I have replaced gaskets on the manifold a number of times so might be able to handle this. Are you talking about O rings that would be inside the casing where the levers are attached in the picture above?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top