Recent content by gusbratz

  1. G

    Case 430 Lift Arms Hydraulic Leak

    take the seat off, then take off the giant reared cover with the rockshaft on it. flip it upside down and you will be looking at the hyd cyl for the draft arms. if it is leaking you will be losing hyd fluid and gaining transmission/rearend fluid level. it is normal for it to drift down when...
  2. G

    'New to me' Case 430 Diesel Questions

    the older ones had 4 intake heaters spaced along the manifold flatpicker, because their are 4 in a row at a glance they look like glow plugs. The newer ones just had one big heater in the top of the manifold. I hooked it up once and mine still would not start without the block heater so I...
  3. G

    570 case power steering cyl repack?

    i have what i think is a 570 or 530 case tractor with the 159 gas engine in it, it has 2 small power steering cylinders under it that look just like this. [/url] https://www.youtube.com/watch?v=ughkLAZejVU I removed both of them today and took them apart by removing the snap ring accessible...
  4. G

    Super A low oil pressure

    I have been working on a super a for a while now, the block was cracked and I was ready to give up. a lady sold me a rebuilt engine out of a super C her husband (soon to be X) had lost interest in. The super C engine had new high compression pistons, was bored out and had fresh valve job very...
  5. G

    530 188 diesel won't start

    I got my pump back from "thepumpguysc" yesterday. He was real nice to work with, good communications and fast turn around time. He said the pump was under fueled, the transfer pump vanes were worn out, the metering valve was beyond worn out, and I had placed the timing marks on the coupling in...
  6. G

    case 530 triple range chatters in reverse

    sometimes if I am backing up fast the transmission/rearend makes a loud clack clack clacking noise. I am not sure what it is. (maybe it's the brakes grabbing and releasing?) I have had the cover off the transmission and the reverse idler gear seems very sloppy on it's shaft. is it possible to...
  7. G

    530 188 diesel won't start

    agreed, i just figured if it's all ready not working i may as well just take it apart. i have a book on it so i followed the directions which made it easy. i did successfully put a metering valve, upgraded eid weight retainer, and transfer pump vanes into this tractor 4 years ago, and in my...
  8. G

    530 188 diesel won't start

    I put the pump on today and blew air through the fuel filters real good. plenty of fuel coming out of the fuel filters but still no fuel coming out of the top of the pump. I give up.
  9. G

    530 188 diesel won't start

    I tore into the tractor tonight. Took the pump off, and all apart. There was a lot of brownish rust inside it from a bad set of filters coupled with a rusty tank I had on it before I rebuilt the engine this winter. The advance piston in the bottom was really sludged up and seemed like the side...
  10. G

    530 188 diesel won't start

    The inlet screen is clean and plenty of fuel flows out of the fuel filters, the return line is clean all the way to the tank. I took the top off the pump today. I used air and blew all the fuel out of the top of the pump so i could see in there. the metering valve goes back and forth when the...
  11. G

    530 188 diesel won't start

    I took the pump window off to check the timing, fuel freely flows out of it backwards from the return line. I tried to start it when the timing window was off. do I still need to try to run it with the return line disconnected? I took the pump apart about 4 years ago and put the upgraded metal...
  12. G

    530 188 diesel won't start

    I am missing something on my 530. over the winter i put new sleeves and pistons into the engine, new bearings, new valves springs keepers. new injectors new fuel filters among a lot of other work. anyway i thought i had the bugs worked out and have been using it just fine. it sat for a couple...
  13. G

    Eagle Hitch Adjusting Screw Stripped.

    I buy a lot of stuff from mcmaster carr, shipping is fast and quality is always good. they have left hand thread fine thread 3/4 rod for 18$ a foot.
  14. G

    Same argument every year

    an old car hood makes a good stone boat.
  15. G

    188 CAV nozzle pressure setpoint

    well they are in and I went with that paper, it said 198 bar (2871psi) and it also said on new injectors to set them 140 psi high so they can settle in. I set them at 3000psi . I hope that is not too high and ruins my pump or something.....
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top