(800) 853-2651
SHOP NOW

Recent content by gutterman

Yesterday's Tractor Forums
  1. L

    Axle weight questions

    I was at a small tractor salvage yard today for some parts & found these weights holding a couple tractors up out of the mud. The only place I have seen them before was pics on this site! Can anyone tell me what they weigh, what to call them, & what they are worth? Just wondering if I...
  2. M

    Ford 2600 Instrument Cluster - Thanks Mice!

    Hello All, I, like others, had a mouse house behind the instrument cluster of my 2600. I believe it is a 1979. Many/most of the wires were chewed to nubs and were disconnected. I would like to preserve the original cluster, which means rewiring. There is enough wire coming from the harness to...
  3. G

    touch control ? lift acts goofey!!

    must hav e sent my reply the same time you posted yours, it was ment to go with the previous post.....haha,
  4. G

    touch control ? lift acts goofey!!

    To check this without taking the cover off, I guess I would change to draft and see if it acts simular to what I have now?
  5. G

    touch control ? lift acts goofey!!

    ok.. update on disc....wife say its fine......now what?
  6. G

    touch control ? lift acts goofey!!

    [ sorry i should have included that in my post, Yeah its a 8n. I wish I knew how to word it to make it understandable, I'll try again, hopefully this will help. When I have something (mower,boom pole,etc) on the 3 point. lets say I have it lifted,motor running, pto on, position control lever is...
  7. G

    touch control ? lift acts goofey!!

    [ok so the friction disc should be checked out, so now what about the lift not going up until very near the highest point of the handle? what im saying is when I first put the top cover back on the lift would start to move up around the center of travel on the touch control, now it starts...
  8. G

    touch control ? lift acts goofey!!

    a i know where it is,what I don't know is how to know know weather it's bad or not ...again the pull down when I'm holding the handle is so much that if I could tighten down the disc I wouldn't be able to move the handle. Also the life eases up. Is that from the disc also? Thanks for the help.
  9. G

    touch control ? lift acts goofey!!

    don't know about the condition of the friction disc really I don't know how to check it...I was thinking that since it worked at first it was fine, the pull on it is so much that I can't imagine a friction disc holding it in place. .other than the disc what else could it be? Thanks
  10. G

    touch control ? lift acts goofey!!

    thanks zane, I checked this morning and it is up. is that the way it should be for normal use? when I'm holding the lever I feel it pulling really hard at times, and the lift wont stay in place, its easing up all the time. is there something that i didnt get adjusted right? when I first...
  11. G

    touch control ? lift acts goofey!!

    Hi all, a while back I had the top cover off and straightened all the bent parts,and replaced the rings,and cam follower pin,and adjusted it using the Zanes tool, it worked great for a couple months, then the touch control started falling (I had/have to hold it up by hand) I can feel it pulling...
  12. G

    loader question??

    thank for the info....couldn't make the trade.
  13. G

    Front carrier done

    OOOHHH HOLD IT RIGHT THERE!!!!! I believe these photos have been messed around with....yeah i said it THERE FAKE!!!....I have proof.....there is no oil spots under the tractor!!!. hahaha.. nice work i like it.
  14. G

    loader question??

    How big of a big deal is it to add a frount pump to a loader that is set up to work off the test port? Does anyone know about what it would cost? Thinking about one, and from what i can tell they are not (much) useable from the test port, as in not having much use of the 3 point,is this right...
  15. G

    pic test

    nice tractor, i have to copy and paste it to see it, but ya its there...i have never tryed to upload from photobucket so i wont be much help, nor do i know how to post a link, hopefully someone will come along and help...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top