(800) 853-2651
SHOP NOW

Recent content by hank woll

Yesterday's Tractor Forums
  1. H

    farmall H generator/regulator for sale

    i have replaced the 6 volt system on my H with a 12V system with alternator-it works well-i would like to sell the generator/regulator if anyone is interested in it-shipping paid by buyer-thanks
  2. H

    charging battery-farmall H

    i did pench that and can't print it-i joined the photobucket sie but still can't get that to print-i'm no computer geek but this is a bit much-thanks anyway
  3. H

    charging battery-farmall H

    thanks-i guess i'll have o figure out how the archives are accessed
  4. H

    charging battery-farmall H

    thanks-looks all inclusive
  5. H

    charging battery-farmall H

    thanks -i'll check thatout
  6. H

    charging battery-farmall H

    my generator has been erratic it seems and now it doesn"t start to charge until the tractor is well warmed up and running for about 30 min.-then if i stop the engine i have a hard time getting started again as though the battery is really run down-probably has run on just the battery for a...
  7. H

    carburetor adjustment

    thanks folks-i have a manual but it isn't very specific as to carb adjustment-maybe there is a different one i need -i'm not too dense mechanically-i rebuilt the engine a few years ago and can do most everything neede to keep her in shape-regards
  8. H

    carburetor adjustment

    i've been having trouble getting my H to ile after she is warmed up-i think i have screwed up the srews to where i'm all out of sync-is there a good starting point to begin to adjust the carb-i'm sure i have messed it up by now-thanks
  9. H

    swapping intake/exhaust manifolds

    thanks andy
  10. H

    swapping intake/exhaust manifolds

    i"m not swapping but just replaced my exhaust manifold with a new one-i torqued the nuts to 20 ft/lbs and started up-ran to warm up and check-all seems well-i need to know if i need to re-torque after she cools off -any ideas and how many ft/lbs-thanks-hank
  11. H

    replacing exhaust manifold/pipe nipple

    now that the manifold is set-i cranked her up and she runs just fine-any good ideas on how much to retorque the bolts on the manifold after warmup and cooldown?-i did them to 20 ft lbs when first tightened up-thanks
  12. H

    replacing exhaust manifold/pipe nipple

    thanks for the help-my manifold is a new replacement as is the pipe nipple so i suspect the antiseize will do the trick-i also plan to keep the tractor under cover as much as i can so rain won't be much of an issue-it's been prety wet here this summer so i probably will get rained on but i think...
  13. H

    replacing exhaust manifold/pipe nipple

    will that keep water out as well?
  14. H

    replacing exhaust manifold/pipe nipple

    does anyone have an idea about what might be best applied to the threads on the exhaust pipe nipple when tightening it into the manifold?-i was getting water in my oil due to worn out threads and did not realize it until recently-i replaced the manifold and have a new nipple-is pipe thread...
  15. H

    exhaust manifold and battery box

    thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top