(800) 853-2651
SHOP NOW

Recent content by Harry Keller

Yesterday's Tractor Forums
  1. H

    Tecumseu

    OK I realize it does run lean with no adjustments on the carbbutit ran fine and startedgreat until all of a sudden the surging and forgot to mention the spitting back through carb until warmed up.. I will check the valve clearance if possible..As you say no problem just because I have to use the...
  2. H

    posting

    Sorry I found it..Harry
  3. H

    Posting

    Posted a message regarding my Tecumseh motor about an hour ago and can not find it anywhere..What is going on????..Harry
  4. H

    Tecumseu

    Hope I am on the right forummMy tecumseu fomula 13.5 hp starts right up and mows gras but when I shut it off when warm it will not start up unless I choke it..Just need to choke it for acouple cranks and it is away...Now thinking it was the carb I installed a new one to no avail as it works the...
  5. H

    M F 10 Vari speed adjust

    I am trying to get my vari speed adjusted properly on my MF 10..The adjustment rod under the dash behind the little plate seems to be the culprit.. Manual states With tractor out of gear and vari speed lever in five turn nut at end of rod clockwise till a bit of slackkNow backout ccw until no...
  6. H

    MF 10 peerless differential noise

    I just can not get pics on here so here is what I found.One needle bearing on main shaft in tranny has a gap between the bearings of sbout half the size of a needle bearing.Going to replace but wondering how to check these??When I put it together last time I put a thrust washer on the end of...
  7. H

    MF 10 part schematic

    Anyone know where I can get a parts schematic for the differential in a MF 10 peerless differential standard shift.I believe 1974..THNKS
  8. H

    MF 10 peerless differential noise

    Thank you..Learn something new every day..Could be it..
  9. H

    MF 10 peerless differential noise

    It is manuel shift and gears look excellent when I had it apart but will do my best to put some pics on here if I take it apart..Actually I am being told these trannys are quite noisy so will wait for a few more answers before dismanteling it again..Thank you
  10. H

    MF 10 peerless differential noise

    The differential is very noisy in all gears but no clicks as a broken gear would indicate or no grinding noises..My guess is a bad bearing or bearings but have disassembled it twice and replaced a couple that looked a bit worn as it is hard to tell if a needle bearing is worn..So I am going to...
  11. H

    74 MF 10 Differential problem

    Got it ..One thrust washer on wrong shaft..Feel a bit foolish.but happens the best of us..Thanks
  12. H

    74 MF 10 Differential problem

    After putting a couple bearings in my MF 10 thehousinggs will not go together ..The input shaft where they meet seems like it holds the casings apart by 40 0r sothou..As soon as I go to snog the bolts to tighten housing it just jams up the input shaft so I cant turn it..O needle bearings loose...
  13. H

    Ferguson sleeves

    Soul have mentioned these sleeves do not have o rings just figure 8 thin gaskets on the bottom..Thanks
  14. H

    Ferguson sleeves

    After installing new sleeves pistons rings ad valve grind and putting this engine together it leas anti freeze around no 2 sleeveso have to take it all apart,,Did I kink the gasket cracked block or what????Should know when I take it apart..Do I need all new sleeve gaskets .and new head gasker...
  15. H

    MF 10 v belt

    Anyone know the correct V belt size from engine down to the implement shaft on a MF 10 garden tractor???Older Model probably a 74..THANKS
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top