(800) 853-2651
SHOP NOW

Recent content by Helsasser

Yesterday's Tractor Forums
  1. H

    70 diesel Crankshaft spacer

    Sorry about the slow response. I ordered a spacer off Ebay and it fixed the problem. Can't believe that much metal wore off the old one but was able to set end play on the crankshaft. And the part number was the same on both spacers.
  2. H

    70 diesel Crankshaft spacer

    Dan you raise a good question. I don't know the history of the tractor. I need to see if I can find the part number of the crank. it looked like it had been worked on from the flywheel nut. somebody could have changed the crank out. The spacer shows very little to no wear. It doesn't have a...
  3. H

    70 Diesel Crankshaft spacer

    The left one was on the tractor A3324R. The right on came from a friend R21624 He said it came off of a G. Its what I need because it has a bell mouth problem is it's to big for the thrust housing.
  4. H

    70 Diesel Crankshaft spacer

  5. H

    70 Diesel Crankshaft spacer

    Picture shows the gap between the spacer and the thrust plate
  6. H

    70 Diesel Crankshaft spacer

    The spacer measures 1.245 and it has the rings showing little wear. The thrust disc measures .162 thick.
  7. H

    70 Diesel Crankshaft spacer

    Key #16 Spacer. and all parts are in place. the clutch is not on at this time.
  8. H

    70 Diesel Crankshaft spacer

    Had crank machined for overhaul. When placing spacer it stops 3/16 from thrust disc. It stops at the radius just before the disc. If I slide crank over so the spacer contacts the disc the disc falls off the crank key. There's no radius in the spacer to meet the crank radius and I split the...
  9. H

    70/720 injectors

    Thanks to everyone.
  10. H

    70/720 injectors

    Bored. sleeved and rebored to factory std pistons
  11. H

    70/720 injectors

    Any issues putting 720 injectors in a 70. I'm aware of the 5 hole vs 6. Thanks
  12. H

    1265 Clutch Tool

    [email protected] Thanks
  13. H

    1265 Clutch Tool

    I noticed those but I don't believe it comes with the flange to adjust the clutch release fingers. Thanks for the reply
  14. H

    1265 Clutch Tool

    Looking for the clutch alignment and finger adjusting tool for the Olive/White/Fiat 1265. Buy rent, borrow or steal. Appreciate any help.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top