-
Hemmjo replied to the thread Picked up these carbs just because.It is good to save stuff like that. If you have room and let someone know you have it. Does no one any good if they just sit in a box... -
Hemmjo replied to the thread long 2610 fuel problem.Where does the blow by come out of?
-
Hemmjo replied to the thread Foam pickup bed protector.My truck is a truck. If the bed gets a ding in it, the bed gets a dig in it.
-
Hemmjo replied to the thread Welding on the Amazing Race tonight.The Welding Engineering Department in college had a huge drop hammer for testing welds. We welded 1/4 x 2 x 2" plates together at 90˚...
-
Hemmjo replied to the thread Zero turn mower.YES it will ruin the motor. It they did not need the far they sure would not have spend money to put them there. As mentions should be...
-
Hemmjo replied to the thread Problem with Predator 3500 generator.Many times, ethanol will corrode components in the carb. In addition it can make the inside of fuel lines flake off. Th particles of...
-
Hemmjo replied to the thread Looking for another idea..You did not put the fan back on backward when you replaced the water pump? It would still move air, but not as good as if it I on correctly.
-
Hemmjo replied to the thread Trouble hooking up.Yep, same age here, a lot has changed in the last few years!!
-
Hemmjo replied to the thread Ford 860 won't run without a little choke.YEP.. siicone is one of the most miss used products on the market.
-
There is a a Ford advertising video made when the Jubilee came out that shows how to mount a plow while sitting on the seat. If the...
-
Hemmjo replied to the thread Trouble hooking up.Ha maybe if I was still that flexable!!!!!
-
Hemmjo replied to the thread Fluctuating Water pressure.I don't see any way for air to get into the pressure tank even if the pump is turned all and all water drained. Not on mine anyway. How...
-
Hemmjo replied to the thread Looking for another idea..If you have changed all of those things and it still over heats it has to be obstruction IN the cooling passages someplace. I recently...
-
-
Hemmjo replied to the thread Exhaust Stud Repair.Ha, it was late, I have no idea how that happened. It was supposed to say “I wore out a couple of bits, but it worked.” I am going to...
-
Hemmjo replied to the thread Exhaust Stud Repair.Do you have any good bolt holes? I did this the repair an aluminum engine block on in a jet ski. Someone had attempted the repair and...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy