(800) 853-2651
SHOP NOW

Recent content by Herck

Yesterday's Tractor Forums
  1. H

    VAO engine stuck solid

    Might be the clip on the end of stater drive came loose, fell and wedged the flywheel. I have had that to happen before
  2. H

    Rollag 2019 part one

    What is the machine called that looks like a brush cutter , chopper ? How was it used?
  3. H

    Name that weed

    I believe that it is Eastern, Gamma Grass, It's a good warm season grass cattle like it
  4. H

    vac-14

    I also had checked the vent line and it was not plugged
  5. H

    vac-14

    Thanks Joe it appears to be leaking near the line fitting in your picture were its marked control valve.It Is not leaking any where else that I can see. Is there any seals internally that could cause this gasket to fail ?
  6. H

    vac-14

    I have a oil leak between the two blocks of the depth control valve were the gasket is. Case says that there are no parts available . So what do I use for a gasket and will this be all that needs to be replaced to stop the leak? Thank You.
  7. H

    Case Calendar Holder

    Made this for Dad to go with his Case calendar. The tractor is a 1948 Case LA. He has owned it since the mid 60"s.
  8. H

    ca final drive clutch

    Im working on the final drive clutch and according to the IT manual it says to remove a snap ring and it would appear that its between the bronze bushing and end of shaft , cant seem to find it. seems that the clutch pack is stuck in there and wont slide out, was wondering if i could get the...
  9. H

    IH 430 baler

    On a 430 IH baler they use a wood block to keep the plunger in place (center block) what kind of wood is it made from? I need to replace it. Thanks
  10. H

    vac-14

    I have a VAC-14 tractor and was wondering what size plow this tractor would pull in a sandy- loam soil
  11. H

    plow

    I have a horse drawn single bottom sulky plow that was made by David Bradley and was wondering if any body could tell me the paint color(s) that would have been used. Thanks
  12. H

    cinder bed

    I was wondering if a cinder bed off fo a state snow plow truck would work for spreading lime, I would mount it on a old truck frame and run the hydraulics off the tractor remotes or put a selfcontained hydraulic unit on and run it off the pto, any ideas welcomed thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top