(800) 853-2651
SHOP NOW

Recent content by Hoboy

Yesterday's Tractor Forums
  1. H

    105 hyd leak

    There are actually many seals/o-rings on the spool and the one giving you the problem is a very small one located on the detent spool. You can pull the spool out but be careful and not lose the detent balls. Put the seals on and reassemble and put grease on the detent balls so they don't fall...
  2. H

    2-150

    I just got a White 2-150 that runs out good and everything works. But the problem is a building collapsed on it and damaged the cab everything else is fine. What should I do find a different cab or make it an open station. I could go either way. Just looking for some opinions. Thanks
  3. H

    2-155 with 5.9 Cummins

    I installed a lot 5.9 into 2-135 and 2-155 and had no problems power wise and the customers were more then happy with the power and torque. They especially loved the fuel economy even compared to the 8.3. I installed 8.3 also but had the beat comments on the 5.9.
  4. H

    PTO delete 1755

    I am looking for the shaft and bearing holder for a 1755 PTO delete. I already have the cover but I am looking for a shaft number of 30-3061426 with a bearing holder number of 105465A would like to buy or at least the dimension of the shaft such as length. Thank you in advance for any help.
  5. H

    500 inline pump swap

    It is a direct swap onto the engine. You just time it with the inline pump method. You do have all the injection lines with it though for the rotary ones will not work, but the inline pump will bolt up to the existing injectors.
  6. H

    JD 450 steering clutch

    I am trying to remove the steering clutches from a older dry clutch 450. I know you have to pull the upper pinion shafts for the final drives to get to the innershaft for clutch removal. But what special tool do I need to pull them. I can not get anything to thread in. Is that a JD special...
  7. H

    Fiberglass grill for 1755 and up.

    Does anyone make a fiberglass replacement grill for the 1755 and up series instead of the heavy cast one that is found on the tractors.
  8. H

    High Track Drive vs Low

    I have worked on both the high drives and low drives LGP and if I was using it in deep wet soupy material I would definitely go with the high drive for it keeps most of final drive from the water/slop working in the worst part of it. It does not have as many final drive failures. Also the under...
  9. H

    970 powershift removal

    In order to pull the powershift clutch pack on Case 970 do you have to pull the cab like they say in the book or can you get the shift cover out with out doing it and what should I watch out for. The clutches are slipping and burnt that is why we are taking it out. Thank you
  10. H

    white 2-155 steering control unit

    About 2 to 3 hours of out of position work
  11. H

    SC Case late model

    I just did one about a year ago where I too needed a sleeve for a newer SC and could not find one. I wound up having one made at a machine shop out of sleeve material that they cut down. Cost me $75.00 but well worth it. That is the route you might have to take.
  12. H

    JD 350C Steering clutches

    Does any body have the height dimension for the steering clutch fingers for an assembled pack. I cannot seem to find that setting in the book. It does say to use a JD special gauge but I do not have that. There must be another way to set it. THANK YOU>
  13. H

    I would rather be working on the 1370

    I am an old construction mechanic and the worst job was doing undercarriage especially if they never used never seize. Your torch is your best friend and you still pray that do not twist off. When you reassembly use copper based never seize that is what even Cat recommends. For track rollers...
  14. H

    My balls do not fit

    Where are located in Wisconsin and how much are they. I live close to Dale/Appleton. Or call 92o- 284-o5o1 and leave message.
  15. H

    My balls do not fit

    I have a 1650 that I needed the lift arm balls for. I got some different ones that were from Agco that was a part number 105967A and they do not fit. The outside diameter is about 1/4 inch too big. So I tried some aftermarket ones and the same thing. I looked in the book and they do not show me...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top