(800) 853-2651
SHOP NOW

Recent content by hotdawg22

Yesterday's Tractor Forums
  1. H

    Need help on my 5050 hydraulics

    OK, Great, found it all and did everything you suggested. Flushed it all 3 times and pretty much cleared up the water contamination thing. However, the lift won't work. I pulled the high side of the auxilary unit and has so little presure i can stop it with my hand. Must have trashed the...
  2. H

    Need help on my 5050 hydraulics

    I really need some help on this situation. All the recent rains in Texas lately has caused me big problems with my 5050. I got it stuck in my back 40 so to speak and it was bogged down deep. The rain just kept coming and it got up over the transmission and displaced all the oil in the hydraulic...
  3. H

    T 340 Serial Number Location

    OK thanks. Just my luck. lol According to the internet source i found, the SN was supposed to be on the bell housing on the right side of the engine. I did find a flat spot there that has absolutely nothing on it, i used a wire brush in my air tool to clean that spot and nothing. I then found...
  4. H

    T 340 Serial Number Location

    Hello all. Just picked up an International T 340 Crawler and started working on it as it had water in the oil. Anyway, my question is about the SN location. I have looked at the bell housing and no number. However, i found a number on the side of the engine block in raised numbers right about...
  5. H

    8N transmission locked up.

    Good point and i did not think of that. It would have to be one of the small gears at the bottom of trans that i can"t see without taking it apart so guess that is next move. I will post what i found.
  6. H

    8N transmission locked up.

    You know, i just thought of something and you may have the answer. If the trans is locked up for what ever reason, could that also lock the differential into position giving the illusion that it was locked up too?? I mean, if the output shaft fron the trans to the drive shaft was locked would...
  7. H

    8N transmission locked up.

    This is hotdawg22 and am interested in your parts. Email me with what you have and prices. thankls
  8. H

    8N transmission locked up.

    OK. I think i might have answered this but here again. I did try to turn engine without engaged clutch and engine spun freely. Let clutch out and it actually turns less the 1/2 turn in either direction and locks up. Took out the forks and made sure the slide were not in 2 gears and still the...
  9. H

    8N transmission locked up.

    So in your opinion what do you think could be the problem as i have scrated my head on this one and can not figure what has happened and what is the solution. I hate like L to break all this down but guess i am going to hafta do dat.
  10. H

    8N transmission locked up.

    Yes, i got the shifter housing off, the shifting forks are out and the hydraulic cover is off and visably everything looks OK.
  11. H

    8N transmission locked up.

    I did. I jacked rear completely off the ground and the wheels spin in oposite directions, the drive shaft does not move. I jacked up one side and tried to turn wheel but drive shaft will not move, not even a wiggle. Locked up.
  12. H

    8N transmission locked up.

    Yes i did try with the clutch engaged and that was when it would just turn so far. I went out now and pushed the clutch in and the motor turns freely, soooo it has to be in the trans. The rear end won"t move and the limited movement i can get out of the trans is limited to the trans cause the...
  13. H

    8N transmission locked up.

    I need some hands on prior experienced expert advice on this tractor and have had good luck on this forum before, so here goes. I bought this 8N that the trans was locked up on. Went to smiths old tractors and followed his advice and I was then able to put all shifters back into neutral or so it...
  14. H

    8N connecting rods

    I did replace the sleeves and the rods are still on the same pistons with new rings installed. I know the engine was rebuilt 3 years ago and it was abad job so everything has been re-done. I mentioned above that the bearing keeper tabs were installed opposite each other and the align perfectly...
  15. H

    8N connecting rods

    Maybe you are in the business of doing mechanic work. ??t I come here for expert advice and usually get so thank you for your comment.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top