(800) 853-2651
SHOP NOW

Recent content by hvwilson

Yesterday's Tractor Forums
  1. H

    3010 parts needed

    I am looking for the bowl that goes on the bottom of the air breather. I didn't think it would be that hard to find on ebay but not having much luck. Anybody know where I could get just the bowl or know if any other models will work?
  2. H

    John Deere 2010 - Problem Starting

    Hey Ben, I don't know how to get in touch with you but I would like to see if you would be willing to work on my 3010 John Deere.
  3. H

    another 3010 PTO question

    thanks for the quick response Tim. I will check the linkage. I did forget to add something. When I start the tractor the PTO shaft spins at what looks like normal speed. Then once the tractor starts it turns real slow, I can stop it with my hand.
  4. H

    another 3010 PTO question

    I bought a 3010 yesterday and the PTO doesn't work. So like everybody I read everything I could about it and before I split the tractor I wanted to ask a few questions. So first thing I tried was the penny trick. I turned the shaft until the pin went in all the way, I felt it move into...
  5. H

    New Holland 320

    roll the baler over with the flywheel. If the forks moves back and fourth OK then most likely everything is fine. Then go around to the deliver shoot and open the door. Check the rollers to make sure none are missing the little plastic cover. If they are replace them. A warning sign you...
  6. H

    New Holland 320

    I've got one, good baler. Make sure you check the delivery shoot. If the bearings go down it's a very expensive fix.
  7. H

    need parts/NH baler

    I have NH baler witha destroyed feeder bar. I found a post where a guy converted his 320 to the same system used on the 315. I am looking for the fingers, rollers and rails off the 315. thanks
  8. H

    fair price for baling

    wow, looks like price is all over. He wanted to pay us $.50 a bale. I thought it was far. I have a ford 3000 and a NH 320 baler. thanks for yalls help.
  9. H

    fair price for baling

    I'm new at baling hay and don't really know how to price myself. What's the going rate for custom baling square bales? Just Baling he is gonna cut and rake. thanks
  10. H

    Anyone have a NH 276 baler to sell/part out?

    Not sure how far west in Ky you are but you may want to try Tri county equipment in Logan county. I was up there this past weekend and they had several used NH balers. They are hard to get on the phone but here is the # 270-542-7854.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top