(800) 853-2651
SHOP NOW

Recent content by Iam2

Yesterday's Tractor Forums
  1. I

    1955 Farmall 300 Utility Steering

    Hello: I have some left over parts from a manual steering I had to buy to patch my power steering. It is an older one than mine was and has the loose ball bearings. If you have found yet me know and I will clean them up and send a pic and see if they are the right ones for you. I had to buy the...
  2. I

    300U crank pully

    Update: pulled spark plugs and the second mark from the bottom right on crank pully is tdc and it is drilled and tapped for the Wagner loader oil pump drive so im thinking it was included in the Wagner kit. Got new distributer and installed it. have been purchasing used gear shafts for the power...
  3. I

    Ih motor cam and crank nut torque?

    Ok well that's the answer I got from 2 local IH mechanics and the local rebuild shop looked on their national computer program and it had nothing, they then told me they usually use Cases comparable readings as they had noticed IH not having this value years ago and just live with it. It didn't...
  4. I

    welding question

    7018, 7018, 7018 there I got it right 3 time for the 2 I didn't! sorry!
  5. I

    welding question

    Make that 7013 FOR THE LOW HYDROGEN rod sorry!
  6. I

    welding question

    May I add my 2 cents worth here as a certified welder having worked 20 years on the high steel buildings in Denver, 2013 is low hydrogen rod which has to be kept in heated can or oven to keep it extremely dry giving very stronger welds but the weld will porous if the rod is not kept heated/...
  7. I

    Ih motor cam and crank nut torque?

    I have been unable to find the torque settings for my I 300U cam and crank nuts which has a c169 engine circa March 1956. In my search I also don't find any for most IH engine for this very necessary 2 important pieces. Also, Im having trouble getting this to post so this is the third attempt if...
  8. I

    300U crank pully

    OK: we opened the distributor completely and found it all gunched up causing it to stick in numerous positions and the springs were shot also not helping the situation and the shafts were severely wore past specs so im looking at going new and bypass the joy of rebuilding and fitting that would...
  9. I

    300U crank pully

    Thanks! You tripped my brain and I borrowed 2 old owners manuals with a wealth of information in them. They go into setting the time in detail and also maintance of the timing advancing system, I have to slow the rpm's down to below 375 as above that it start advancing which will give a...
  10. I

    300U crank pully

    Hello: we have a 300U partially tore down looking for boogered cam keyway and just noticed the crank pully is not the stock pully and it has extra timing marks like a total of four, does anyone have a stock one to check before I tear further? the timing seems to be off as it wont run good...
  11. I

    International 300 utility

    Dave: I had the same problem only worse, mine has a Wagner loader so tank removal is a royal pain so I water washed it as good as I could and air blew it too and installed 10 gallon of discount store white vinegar for almost 24 hours and washed and blew that out and put in a box of baking soda...
  12. I

    remove 300 U fuel tank

    I wanted to share the results of doing things a little different: I opened the tank up and water washed all I could get to flush and then poured 10 gallon of white vinegar in and let that set almost 24 hours, flushed all that out and put in a box of baking soda and water overnight and flushed...
  13. I

    remove 300 U fuel tank

    Well this is deeper than I thought: this tractor has a loader mounted on it and there is a spreader bar going across from one side to the other and removing the steering wheel and throttle mechanism and dash wont let the tank out from the loader crossover so I am going to need to remove the...
  14. I

    Rusty gas tank 300 utility

    Hey D we need to get together here- I have the same issue but I did my leaf blower gas tank last fall and just filled it with CO2 from my mig welder tank and used a shaft drive from my grinder with a Dremel cutoff wheel on it. Be really careful to keep a slow flow of CO2 going so it doesn't blow...
  15. I

    farmall 300 gas strainer

    If he has a hung float with an empty bowl or a plugged additional strainer in the line would blow this .
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top