(800) 853-2651
SHOP NOW

Recent content by Ian Beale

Yesterday's Tractor Forums
  1. I

    99 problems and my tractor is every one of them

    As the saying has it It is more effective to deal with the block than the chips In your case I'd suggest going direct to Kioti in South Korea
  2. I

    Terex Help

    Oz
  3. I

    Terex Help

    A friend down here has a Terex 82 20 B and the parts supply is not so good. Any suggestions for possible sources your side would be appreciated and I'll pass them on Thanks
  4. I

    Belarus 562

    Yes but https://www.visitnsw.com/destinations/country-nsw/the-murray/wentworth/attractions/ferguson-tractor-monument The other grey tractor song that I've met is about this. Can't find it ATM
  5. I

    A little grease gun repair

    If you can find them have a look at McNaught guns. They work with both cartridges and bulk grease, last and they have replacement plunger kits. For priming you pull the rod out and a part turn locks it in the plunger so you can lean on it
  6. I

    Blade of a leaf spring, how to weld?

    I've also had good luck with using arc welding with stainless rods. Just tapered the broken ends and welded. If you happen to have two of the same broken leaves cut them across the centre bolt hole and join the two good ends there. Minimum flex that way
  7. I

    Harbour freight drill bits

    Re "Different factories making look a like stuff" A bloke I know that deals with China reckons you have to visit frequently to check otherwise what you get will be coming out from the second or third door of the same plant
  8. I

    340B Rain Flapper

    The ones we get now seem to have a poly sleeve in the pivot. I walked into our local parts store to hear a customer being shown one say "No more rattles!"
  9. I

    Question for computer geeks

    You could also leave it where it is but try renaming it with one letter different. Easy to change back if it was important
  10. I

    American Bosch Pump ID

    Might be something on the pump here http://www.oldengine.org/members/diesel/Ambac/Fuel1.htm IIRC 90EH is a 9 mm plunger
  11. I

    Joh Deere 7520 4WD pistons??

    Not Deere but might be worth reading for your search https://www.redpowermagazine.com/forums/topic/130025-dont-buy-maxxiforce-engine-kits/
  12. I

    Lincoln Weldanpower 225

    IIRC there is an SAE tapered shaft for single bearing alternators that has a threaded end so you have to unscrew them. I was warned that may take some doing on a 16 hp B & S
  13. I

    Fergie Positioner for Ferguson TEA 20

    Further down there is more including a DIY https://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=ferg&th=141453
  14. I

    Lanz Bulldog

    Jim (after lining up start timing marks) And lighting the "wick" - the slow fuse like treated blotting paper. Story here is of one local who did use a 12 ga with shot.
  15. I

    Lanz Bulldog

    The originals came with a severe warning to not attempt to use in a shot gun
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top