(800) 853-2651
SHOP NOW

Recent content by IH 1586

Yesterday's Tractor Forums
  1. I

    9 BOLT WHEELS

    diameter?
  2. I

    Speedometers

    What happens when the front end comes off the ground?
  3. I

    Speedometers

    get a GPS.
  4. I

    gears in farmalls

    We are in the 10% over class. We run 13.6 tires on a 13 inch rim with about 50% tread, or less, if that helps. Thanks for the info. I was told an allis chalmers wc ring and pinion works as well, is this true?
  5. I

    gears in farmalls

    I have both a Farmall H and Super H and I am trying to figure out the fastest gears possible and not exceeding 3.5 mph. Some of our pulls have a 1st gear only, except in a tractor that has a creeper gear can use 2nd. Some have an RPM limit of 2% or 10% over. Others use the 3.5 mph speed...
  6. I

    M in 4500

    I already have an H and a Super H that runs 3500 and 4500 with a 3.5 mph speed limit. I am astrictly IH guy and was looking for a 4500 5500 tractor. Thanks for the help guys, I will stay in the higher classes where I can add the weight where I need it.
  7. I

    M in 4500

    Has anyone been able to get an M into the 4500 lbs class? I'm sure it would be tough, but a single front wheel, pressed steel rears. I would need to get the tractor to 4500 because I a m a 200 lbs guy and I get 200.
  8. I

    Wanting a lower 1st gear for Farmall H

    Why would you want to slow your speed down? Are you powering out? You want as much speed as you are allowed in general, and you need more power it sounds like, to be competetive.
  9. I

    Craftsman LT1000 belt size

    Can someone help me out with the size of belt for my 2001 Craftsman LT1000? My belt is worn badly and there is no number that is readable. It seemed to be the wrong size to begin with. I just recently bought this mower so this is why I don't know what size the belt is. I'm sure the guy that...
  10. I

    farmall low gears

    We have an H with a low first and second gear. They came from the factory this way, you can find them, you just have to look.
  11. I

    other good tractor pulling forums

    Anybody know of other good tractor pulling forums out there? I am from Minnesota and would like to see where all the local guys are chating, but any site is acceptable. Thanks.
  12. I

    815 V8 motor

    so can you put this motor in an m, that is my ?
  13. I

    stock class thats not so stock any more

    what kind do you have? shoot me an email.
  14. I

    301 gas mods

    Hey guys, I am building up a 301 gas motor out of a 715 combine to put in my 460. How big do I have to get the cubes in order to get up in the 130 hp range? You can email me if you dont feel like sharing here. Thank you
  15. I

    815 V8 motor

    Has anyone used a V8 out of a 815 combine motor in a pulling tractor? I know these were loud fast running and powerful. Does anyone make an adaption plate?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top