(800) 853-2651
SHOP NOW

Recent content by IH4386

Yesterday's Tractor Forums
  1. I

    What equipment tiled this field?

    Looks like it was chisel plowed or ripped while there was some frost in the ground. Here in Wi ground will look like that after doing so with an inch or two of frost.
  2. I

    hough h90e

    Hello, I am looking at a hough h90e payloader and am trying to figure out what year the machine is. The serial number is 3560307u001914. Any help would be appreciated.
  3. I

    3020 starter question

    The two group 31 batteries will be connected in a parallel set up which will double the cranking amps. I agree on the cast nose cone. will the nippendenso from a 4440 be clocked right and will it fit?
  4. I

    3020 starter question

    I have a late 3020 that I will be rebuilding the starting system on. I will be replacing the 2 6volt batteries with 2 group 31 truck batteries an fabricating new battery boxes to fit new batteries, installing all new 4/0 battery cables from ground to starter, the starter will also be replaced as...
  5. I

    3020 Steering valve conversion

    I have a late model 3020 that serves as our loader tractor and as of late there has been a leak under the dash in the steering valve, Ive cleaned all fittings to find that none of them are leaking but found the leak to be coming from where the two housings bolt together which Im guessing the...
  6. I

    Hydraulic spool valve

    Ahh. Thank you. I was getting pretty frustrated with it last night and I am doing the repair without removing the stack of valves from the tractor. I will try removing that bolt tonight after work. Thank you very much.
  7. I

    Hydraulic spool valve

    Hello, I'm working on my spool valves on a 4386 and they are leaking oil out around the check valve retainer caps. I've removed the spool itself from the valve and removed the retainer ring holding the check valve in but am having trouble removing the check valve to replace the o-rings, I...
  8. I

    20 series wheel casting question

    I just got the casting numbers from the wheels, they are actually from a 3010 and the number is R31610R would that still work with the larger axle wedges. Thanks.
  9. I

    20 series wheel casting question

    I have a 4320 that sits on 34" rears right now and would like to go to 38" rears, I have a chance to get the 38" castings from a 3020 and was wondering if the 3 1/8 axle castings from the 3020 would fit the 4320 by using the 3 3/8 casting wedges. Thanks in advance for any info.
  10. I

    Fitting a QT1 Year A Round cab on a side console 3020

    E-Mail sent. Thank you very much for your help.
  11. I

    Fitting a QT1 Year A Round cab on a side console 3020

    I've thought about doing that as a last resort as I would like to try and keep everything original to the cab side of things when installing the cab. I cannot find any pictures online that show the filler panels around the floor or by the pedal areas. Was thinking someone might have these laying...
  12. I

    Fitting a QT1 Year A Round cab on a side console 3020

    Hello all, I am attempting to install a QT1 Year A Round cab on my side console 3020. If possible could those of you that have this cab on a 10 0r 20 series tractor post some pictures of the filler panels on the floor board and around the pedals as the cab I have is incomplete and I am not sure...
  13. I

    OT-trapping woodchucks

    I just got two of them about an hour ago. We had them dig under one of the grain bins, the area around the bins is all mowed grass and I have found it best to sit and wait for them to come out in the evening and get far enough from the hole entrance and then take the shots needed to prevent them...
  14. I

    Equipment shed bird problems

    Hi all, was wondering what some of you do to keep the birds out of your sheds. I have the balloon bird eyes in each of the big doors and also the bird be gone audio system and it doesn't seem to phase the sparrows from entering and making nests, just wondering if there is a better way. Yes I do...
  15. I

    4960 lift assist cylinder

    I have a 4960 with the left hand side 3pt lift assist cylinder that is leaking at the shaft seal, I haven't looked closely at the cylinder yet as currently working on rebuilding the input planetary clutches at the moment, My question is can the cylinder be taken apart easily to replace the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top