(800) 853-2651
SHOP NOW

Recent content by IH856custom

Yesterday's Tractor Forums
  1. I

    Auger swing 1420 combine.

    I have a 1420 IH. The auger swing is slow. I’m wondering if the steering hand pump is the problem? In the service manual. The flow dividers. Give steering priority over auger swing and reel lift. As of now mine is working when I manipulate the steering wheel. There is an Orifice before the hand...
  2. I

    What is an 856?

    Thanks, I I know. When I Order parts. Just wished I knew before I put the wrong IPTO shaft in. Live and learn. Education is never free.
  3. I

    What is an 856?

    my 856 custom falls in to the Farmall coding system. Farmall codeing system 1926-1971. However IH was using anther coding system. Post 1971. Some of the models fall into both coding systems. That why I put the wrong IPTO In my tractor. Now has winding noise in the middle.
  4. I

    856 ih ipto . Winding noise.

    inally figured it out. I do have the wrong IPTO. Some where along the way. It come down to reading serial# international and farmall was useing two serial number coding systems at the same time. I have the IH 856. The code falls into the farmall coding system. That why the prat break was...
  5. I

    What is an 856?

    im trying find out about the serial number. If the 856 was classified as a Farmall or an International.. when buying parts. Both are listed but have different serial number listings. The iptoshaft falls into a parts break on the serial number.
  6. I

    What is an 856?

    serial number tag says international harvetor.
  7. I

    What is an 856?

    custom. I thinking it falls into to category of a farmall.
  8. I

    What is an 856?

    custom.
  9. I

    What is an 856?

    It doesn't say farmall on it anywhere.
  10. I

    What is an 856?

  11. I

    856 ih ipto . Winding noise.

    No can't read old shaft
  12. I

    856 ih ipto . Winding noise.

    Ih S/N # break 9493. Mine is IH 856 custom S/N 27257sy . Mine should have 25 degree. Farmall S/N # break 27287.
  13. I

    856 ih ipto . Winding noise.

    I recently baught an 856 IH. I had to replace the clutch and theIPTO. Shaft. When I got the ole gal back together. The tractor has a loud winding noise in the middle. I'm pretty sure I ordered the correct shaft. Hydraulic work fine. As the tractor warms up it does get a little quieter.
  14. I

    Gehl wagon weight rating

    Anyone know how many ton? A gehl model #c1006 running gear. I'm thinking it's a ten ton.
  15. I

    856 IPTO stripped out

    I recently bought a IH 856. I was told about the clicking noise in the transmission. The tractor has been sitting for about eight years, I finally get the old gal running. It has a loud shrilling noise in the bell housing. Sounds like a bearing going out. Power steering is gone no brakes and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top