(800) 853-2651
SHOP NOW

Recent content by IHCC51

Yesterday's Tractor Forums
  1. I

    Farmall c with 404 engine issues

    Thank you for the advice Jim. I will give it a try, Steve
  2. I

    Farmall c with 404 engine issues

    In order to get required rpm for HP required to run my mower I have to extend the carburetor linkage and it will not idle down so regardless of throttle position I have 1 speed. Thank you for answering. Steve
  3. I

    Farmall c with 404 engine issues

    I am using all original linkage , when I adjust according to the manual I get a max of 1700 rpm s with full adjustment to the governor speed adjusting screw. In order to get higher rpm I have to adjust the governor to carburetor linkage longer but then lose low idle. Thank you for answering. Steve
  4. I

    Farmall c with 404 engine issues

    I have my Grandfathers 1951 Farmall c, the engine in it when I got it was a c123 with a bad head, I replaced it with a c135 from a 404 so I could pull my mower. The c135 runs at 2,300 rpms the original c113 ran at 1,875 rpms so I wanted to run the c135 at about 2,100 to not get too far above the...
  5. I

    farmall 140 radiator with 404 engine

    I run it wide open about an hour to finish mow 7 acres with a mower that requires 35 PTO HP ( that is why I put the 404 engine in Grandpas C ). Thanks for the reply Steve
  6. I

    farmall 140 radiator with 404 engine

    I run it wide open for about an hour to finish mow 7 acres with a mower requiring 35 pto hp ( that is why I put the 404 engine in Grandpas C ). Thank You for the reply Steve
  7. I

    farmall 140 radiator with 404 engine

    I put a 404 engine in my grandfathers Farmall C . Neither the C or 404 radiator would work , I was advised that a 140 radiator would work. I bought the cheapest new one I could find and it did work. Now the tractor runs hot, if I put the grill and hood on it is into the hot range. Without them...
  8. I

    farmall c loader

    I have a 1951 Farmall c that has a 404 engine in it and a loader that I run off of the original touch control hydraulics. I am wanting to get more hydraulic power and am looking at a few options such as running a hydraulic pump off of a belt which also runs the fan water pump and generator. I...
  9. I

    IH 404 engine in Farmall C

    Thank You I will try to locate 1 Steve
  10. I

    IH 404 engine in Farmall C

    Beware: I put an engine from a 404 in my 1951 C to get the manufacturer recommended 35 PTO HP to pull a finish mower. My decision was based on advice from this site. My options were rebuild and power up the weak super C engine already in my Grandfathers tractor or replace its engine. My thinking...
  11. I

    farmall C hydraulic line 404 oil dipstick conflict

    Thank You DeltaRed, I have some fittings ordered for the lines. The oil pan part numbers did not match up.Steve
  12. I

    farmall C hydraulic line 404 oil dipstick conflict

    I have recently began putting a farmall 404 engine in a 1951 farmall c because I thought it would bolt right up. Well my latest issue is the oil dipstick from the 404 engine - casting # 375596R1 - is in the same spot as the touch control metal lines from the hydraulic pump need to be. Has anyone...
  13. I

    IH 404 timing gear alignment

    Thanks for answering Mike. It is a gas engine. The ones I have seen in the past had 1 dot line up with 1 dot. Thanks Steve
  14. I

    IH 404 timing gear alignment

    I bought a c-135 engine from an IH 404 to put into my Farmall C. I noticed a bad distributer / governor drive bushing and when removing it some filings from it fell down behind the timing cover , so I removed it to clean the filings out. Then I noticed the cam timing gear has 3 dots on it . When...
  15. I

    farmall c rebuild

    Dave, Thank you for your reply. When I take the # 1 spark plug out after running it I have a couple of tablespoons of anti-freeze on top of the piston and if I don't draw it out it works its way down to the oil. Also my compression reading is low on # 1 ( only about 85 psi ). I followed...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top