(800) 853-2651
SHOP NOW

Recent content by IMAMAC

Yesterday's Tractor Forums
  1. I

    brake shaft bushing removal

    Ok, thanks guys. They are copper so they are pretty soft so I'll give it a go with the chisel and see how "easy" they come out. I appreciate the advise!!
  2. I

    brake shaft bushing removal

    Hey guys, I'm replacing the tires and brakes on my 9N. I got some new bushings for the brake shafts where they anchor into the transmission case. How do I get the old bushings out?
  3. I

    12 volt wiring

    Thanks guys! I got it running with your help. The starter switch plunger was too short. I soldered two pennies on the plunger and make it longer. Everything works great. The ammeter reads total load too. Fantastic. I really appreciate the help.
  4. I

    12 volt wiring

    Ok, Im glad. I thought I was going nuts. Thank you very much.
  5. I

    12 volt wiring

    ok, I installed a new starter switch, new starter, new battery cables. My tractor isn't even rolling over. I wired according to JMOR and I got no action. Can someone please take a look and see if they can see anything wrong? When I jump the starter post directly from the battery, it rolls...
  6. I

    12 volt wiring

    Ok, thanks Bruce. So, When I replace the ballast resistor and remove the ceramic resistor, Im going to hook the brown wire that feeds the coil directly to the ballast resistor and remove the orange wire? Correct? The JMOR wiring diagram shows the big yellow wire that feeds the starter switch...
  7. I

    12 volt wiring

    Yes, it has a 12 v coil. It came with the conversion kit. I don't know what you mean about a ballast resistor, is that the original 6V resistor that cooked when hit with 12V? That would be the top resistor, which is mounted horizontally in the posted pic. The ceramic resistor came with...
  8. I

    12 volt wiring

    Ok, so I have a Ford 9N. I installed a 12V conversion kit. I tried to start it, it didn't fire up, I have no spark. I see that my original 6V resistor is toasted so that is probably the problem. I thought I followed the (very poor) instructions and had it hooked up properly but I guess...
  9. I

    What the heck is this cable?

    Wow, that's it alright. very cool. I got it soaking in PB blaster so hopefully it will free up and I can use it. Thanks so much for the info...
  10. I

    picture of cable

  11. I

    What the heck is this cable?

    Im installing a new clutch in my 9N. I have had this tractor for a few years but don't know too much about it. There is this cable sticking out of the dash, I don't know what its for and didn't know what its hooked to, until I split the tractor for the new clutch. Is this a 2 speed gear box...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top