(800) 853-2651
SHOP NOW

Recent content by Iron Kid

Yesterday's Tractor Forums
  1. I

    f corn head

    Yes it would. Wilber Nebraska Southeast part of the state.
  2. I

    f corn head

    Looking for a 4 row 30 inch corn head for a Gleaner F2.
  3. I

    720 pony start

    Is it possible to convert a pony start engine on a 720 from 6 volt to 12 volt?
  4. I

    all crop 60 sickle bushing

    On my all crop where the sickle attatches to the drive need to no what bushings go there, are they rubber or wood? Can a person make something ?
  5. I

    ford 5000

    Going to look at a 66 ford 5000 DSL with an sos trans. The owner says motor and transmission was rebuilt, but the hyd and reverse is slow till it warms up. Any ideas what it could be or what to look for? Have not seen it yet. Thanks
  6. I

    radiator

    Looking for a new radiator for my 961 diesel, where is a good place to get one? Its an Every day user.
  7. I

    one armed loader leak

    Ther is a screw with a copper flat washer on the upper end of the cylinder, believe its a bleeder, cannoy get it to quit leaking. Is there supposed to be a gasket or do i need a new copper flat washer? This is on a ford 711 loader. Thanks
  8. I

    841 power steering leak

    My 841 that I"m selling developed a power steering leak, which is coming out around the steering wheel. Looked in the repair manual and see there is a shaft seal on the steering shaft. Any tips or suggestions on removal and replacing it? Thanks
  9. I

    heat houser

    Looking for a heat houser for an 841 ford. Any suggestions?
  10. I

    Hyd Valve ID

    Have a remote valve for my 841 ford wondering what type, parts or manual for it. Say"s parker on the valve. can email pictures. thanks
  11. I

    all crop straw rack

    On my ac 60 the end of my wood straw walker by the cylinder busted out at the hinge. Any advice for taking it out or repairing it? Have a neighbor with a couple in trees hoping to get a good piece to repair or patch mine.
  12. I

    bin unload for ac combine

    Thats what I thought!
  13. I

    bin unload for ac combine

    How do you change the bin unload auger belt on an ac 60 combine?
  14. I

    all crop 60 canvas

    The old one that is shot has metal strips with stove bolts holding them together.
  15. I

    all crop 60 canvas

    looking for the short top canvas for my ac 60 combine
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top