(800) 853-2651
SHOP NOW

Recent content by itsb

Yesterday's Tractor Forums
  1. I

    house driveshaft

    thanks I sent you an e-mail
  2. I

    house driveshaft

    I meant to say Howse
  3. I

    house driveshaft

    morning all, I have an old house bush hog and the slide-spring and role pin are gone,I've been told you can't order them any longer, short of having a machine shop make one, anyone know of an source for them. thanks bob
  4. I

    Welding rods

    them are DC rods, just think about it they are designed to burn on DC which is direct current (meaning contuous burn) not AC as in altering current (meaning burn-break-burn) ya some do make it work, but why not just use the correct rod for the box. like they say--just cause you can get it on...
  5. I

    1920 ford differinal

    that was it MHB, the top part of the dipstick is gone just enough to seal and a little bit of the dipstick end sticking up. thanks again bob
  6. I

    1920 ford differinal

    thanks, I have a manual ordered, but until I get, if there is a dipstick is it under the hood or on side of trans, I have looked but not finding it. thanks bob
  7. I

    1920 ford differinal

    to check fluid level is it the 2 plugs on the left side of trans, upper one I would use a 11/16 wrench and lower one about a 7/8, and if so why 2 different sizes. thanks bob
    • itsb
    • Thread
    • Replies: 5
    • Forum: Ford
  8. I

    3910

    thanks dave, I was looking at buying one and all my stuff has cat 2 and rather than change all the pins it would be easer and cheeper to change the balls. thanks bob
  9. I

    3910

    morning all, on a 3910 can you change the balls on the lift arms from the original cat. 1 to cat. 2 I know some tractors you roll them to a slot where they will pop out thanks bob
    • itsb
    • Thread
    • Replies: 4
    • Forum: Ford
  10. I

    frount end loader

    thanks Leroy, I will look again
  11. I

    frount end loader

    jacksun65 what town was that loader listed under I tryied searching but I failed thanks again bob
  12. I

    frount end loader

    ok thanks everyone, jacksun65 I will look it up but that's a far piece form central mo. thanks again bob
  13. I

    frount end loader

    morning all, have a jd 5300 4x4 I need a FEL for it, I found a jd 400-cx for sale but I need to find out if it will fit my tractor. Also I have found other loaders I might be interested is there a site that has a chart as to what will fit what thanks bob
  14. I

    CC again

    I'm in the troop that don't worie about it,I do see where it is headed,it will be like auto insurance you will have to also Carrie uninsured policies ! Which means you will be insuring the scum bag that is trying to do you harm !
  15. I

    man is it slick

    Thanks Leon I know that you adjust to the imp.but they make different length top links for different model tractors! Yes the seatbelt is to be used with ROPs,but also it would not be comfortable reacted down to the seat . I'm 58 years old and I started pulling a rake when I was 12 so I'm no...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top